Question about Zanussi ZWF1420W Front Load Washer

1 Answer

Leaks seems to leak on hot wash

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 373 Answers

Try checking the hot water inlet hose for leaks.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leaking washer, increases when using cold, less when using hot. May be at drain?


Stop the washer and clean up the water. Confirm that the water is not leaking when the washer is off. The leak can occur before the electric valves either where the hose connects or from the electric solenoid valves just inside the washer. The situation is more likely true if the hoses are stressed by being bent to one side.

If dry then confirm if it is the hot or cold by running the machine with the cold service valve open and hot closed.


26040560-ygp4wnkres3ekniwc32iwowp-4-0.jpg

Jan 06, 2016 | Washing Machines

1 Answer

Leaking fisher & paykel smart drive 501


Check your hot and cold hoses at the back for leaks,
these are just crimped on plastic ends and can crack and leak..

Jan 13, 2013 | Fisher and Paykel Washing Machines

1 Answer

Water coming out of the bottom of the machine


Sometimes, what may seem like a washing machine leaking from bottom locations is actually one that leaks slowly from other spots. Slow leaks can accumulate beneath your washing machine making it seem like you have a bottom leak. For more help identifying the exact point of the leak, see Washing machine leaking.

Bottom leaks may be better identified using a newspaper. Just dry the floor and lay the newspaper beneath the washing machine before you test for leaks. Darkened sections map out your water leak. This method is not always foolproof, however. The best diagnosis will come from a qualified service professional inspecting your machine.

If your washing machine is leaking from bottom in the rear, you may need a replacement pump and professional installation. The leak could also be caused by a faulty air dome seal or a hole in the tub. For more troubleshooting steps to tackle that leak, see Washing machine leaking from bottom. I hope that helps!

Sep 27, 2012 | KitchenAid KHWS01PMT Front Load Washer

3 Answers

Leaking water from bottom


Hello there:
If the washer leaks all the time, check these: Hot and cold water fill hoses - Check the hot and cold water hoses from the household plumbing. If either hose is leaking, tighten it or replace it, as appropriate. Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace. You probably should call a qualified appliance repair technician. Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you need to replace it. Outer tub - Over time, the steel or plastic outer tubs can rust, split, or be punctured. If this happens, you may have to replace the entire outer tub-

Apr 18, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Water flows in cold side of water valve and out hot side valve


It seems unlikely that something went wrong just from moving it unless it got banged up!
It sounds like you may have stripped the hot side.
I'm assuming the water is going in the cold side and out the hot side and out the back.
If this is so and you are happy with just cold water try this:
Go to a Plumbing Store and buy a cap for the leaking intake...if it still leaks you can try soldering the two together!
I hope this was helpful.
Good Luck!

Jan 20, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Leaking Water


check your rubber bellow you might have had something go threw it.

Jun 22, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Leaking washing machine


how did you get into the front of the washing machine? did you have to take it all apart (including dryer???) is there a simple way to open the front of the washer?

Mar 02, 2008 | Washing Machines

2 Answers

Leak in washing machine


can you tell where the water is hitting the belt from is it in the middle of the wash tub or from the outside of the wash tub please let me know if its from the middle of the tub its probably the seal that keeps the agitator from leaking, and if its from the side the in lines from the water spicket or the valve that controls hot and cold in the machine could be leaking, please look closely and try to see where the wateris dripping down from. thank you, then let me know

Dec 21, 2007 | Washing Machines

Not finding what you are looking for?
Zanussi ZWF1420W Front Load Washer Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...