Question about Microsoft LifeCam NX-6000 Webcam

1 Answer

Error Msg: Problem occure during Hardware installation

Dear Friends

I am facing a critical problem. I am using WinXp and couple of days back I installed My NX6000 cam in laptop (Pariso V3000 model) which was working absolutely fine. Then after that I installed Logitech Cam in my laptop without uninstall my NX 6000 software and Logitech was also working fine.
Then I uninstall Logitech and try to run NX6000 it was not working.
Then I uninstall NX6000 driver completely and Installed as a fresh .. but still it unable to detect the Cam,when I try to click the cam application ,it showing error : "Problem occur during hardware installation, plz chech audio video setting".

I checked the setting option from cam window / interface and audio ( speaker / mike) is working properly.

The main problem is System unable to detect the hardware.
I also tried to clean registry and uninstall NX6000 driver and again reinstall it... but every time it gives teh same error "Problem occur during hardware installation ".

i WILL be thankful if someone can suggest....any workarround,,

regards

Soumen

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Having Nero installed can cause this problem. This is from the Microsoft Knowledge base. There are some other programs that can cause this problem. Search "Lifecam Program" I believe I have tracked the problem down to this. I have not uninstalled Nero yet, But Nero crashes when trying to launch it video utilities. So at this point I am presuming that tere is a conflict.

Posted on Jan 22, 2009

  • pnimirowski Jan 22, 2009

    Sorry, THis does appear to be the fix. I tried everything including installing the old lifecam program. The old program I could get half going. THe newest verison no way. I am just going t replace the web cam. There is a flaw in the software. This problem started after I built a new system. Running XP Pro SP3 on a Intel Quad using a ASUS Rampage MB, ASUS Video Card ATI 4850.

    There's a conflict somewhere. I even dusable the ASUS virtual capture. Had a Microsoft tech go into my computer, he gave up as well. Say's other's have had the problem and they (microsoft) do not have a solution.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Well my web cam used to work just fine but like now when i open up the microsoft lifecam it says initialization error and whenver i try to put the camara to my friends on windows live before they used to...


1st You download Webcam Driver.
Well my web cam used
After this install the Webcam driver in the system.
Installation of Webcam Driver
Go to the control panel
Click on the System Icon
Click on the Hardware Tab
Click on the Device Manager s
Select the Unknown Device or printer device where yellow Question Marks sign on it.
Right click on it and uninstall it.
After this go to the top of the device manager and click on scan for hardware changes.
Driver installation Wizard start.
Brows Your Driver from the Hard Disk and click on next.
Driver will be install.

Jan 23, 2011 | Microsoft LifeCam VX-6000 (68C-00001)...

1 Answer

Windows XP cannot detect driver for my i ball face to face 12.0 web cam


Control panel, add remove programs and windows components, list of installed programs.
Find the related program or component choose to remove it.
Back out and reboot.
Make sure the hardware is not connected and use the installation CD. Follow installation procedure and itw wizard will address the point to install the hardware connection. At that point connect the hardware and proceed to Finish.

Aug 24, 2010 | Webcams

1 Answer

Just downloaded my Genius Look 313, continuosly getting msg., " camera being run from another dvice" how do I fix this


Copy this site and paste it in your browser address bar and hit ENTER.

http://download.cnet.com/ManyCam-Virtual-Webcam/3000-2348_4-10593500.html?tag=mncol

to your web browser and paste it in the Address Bar and hit ENTER.
Then download the program and install it to start having fun with your camera and friends.

Manycam allows you to use your Webcam with multiple programs at the same time. Broadcast your
Webcam on MSN Messenger, Yahoo!, Skype, AIM, Paltalk, and Camfrog all simultaneously. Manycam
also allows you to add cool live CGI (computer generated special effects and graphics) to your
Webcam. Make it appear as if your face or hand is on fire with our "fire" effect.
Pretend you are underwater or make it look like it's snowing inside your house with the
Manycam underwater and snow effects. Add text, graphics, or your country's flag to your video
window.

ManyCam is the freeware tool for you if you use both CamFrog and ICQ, or any other video chat
program, and you want to use them simultaneously. It creates a "virtual" Webcam that
replicates your currently installed camera. It then lets multiple applications
access the video stream without conflict.

ManyCam is compatible with Yahoo, MSN, CamFrog, PalTalk, ICQ, Skype, YouTube, and more. Once
you've installed ManyCam, you need to set ManyCam as the primary input for program that you
want to use. ManyCam will automatically start when you activate your Webcam through that
program. The application includes a bunch of gimmicky features that let you change aspects of
the background and foreground. You can map a new pair of cartoon eyes over your face, and they
track pretty well to your movements, or you can show that your life is hell by replacing the
background with flames.

NOTE: There is an unfortunate toolbar that will install unless you opt out during setup, but
other than that ManyCam is worthy of a Webcam Oscar for cool and useful tech.

Hope this is of some help. Bud

Jan 05, 2010 | Genius Look 313

1 Answer

An error occurred during the installation of the device.


1st-try to check for virus/spyware, is virus/spyware normal operation syntom. You dont have any admin control to your computer. check for online antivirus like norton, macfee,....

then try uninstall the current drivers, and try install the original drivers. and post again for more steps

Dec 20, 2009 | Micro Innovations IC200C Plus Webcam

1 Answer

I am facing a critical problem. I am using WinXp and couple of days back I installed My NX6000 cam in laptop (Pariso V3000 model) which was working absolutely fine. Then after that I installed Logitech Cam...


Normal 0 Did you install the software with the camera connected to the computer? Disconnect the camera from the USB port and reinstall the software. When the program asks you to connect the camera, do so, and it should work. Hope this is of some help. Bud

Below is info for setting up Audio & Video to chat on line after you install , either Skype or a messenger program.


Web Camera’s have to be setup on the program they are to be used with. Just installing the camera on your computer does not set it up to broadcast on messengers or Skype.

Each program has Options that have to be setup in order for the Audio and Video to function properly.

A. Skype Setup:

After downloading and installing Skype set it up as follows:

  1. Go to TOOLS, then OPTIONS, and click on Audio Settings and set the Microphone and Speakers to the computer Audio Card.
  2. Then click on the Video Settings.
  3. The camera if installed properly will come up and show a picture.
  4. Then on the bottom of the page click on Save.

The camera and audio should function properly. Your friends and Family will now see and talk to you.

B. Yahoo Setup:

After downloading and installing Yahoo Messenger set it up as follows:

  1. Go to Messenger at the top left and click on it.
  2. Next go down to Preferences and click on it.
  3. Next Calling and Devices on the right and set the Microphone and Speakers to the computer Audio Card.
  4. Next go to the Test Audio section and (in blue writing) click on “Open the call setup assistant” and follow the instructions on the left window.

C. Windows Live Messenger:

  1. After you start Windows Live Messenger, expand the view by clicking on the square on top left next to the red X.
  2. Then on the Windows Live messenger window on the right side, click on “ “Show Menus.” And then click on “Show the Menu Bar”.
  3. Next go to the Menu Bar on right side, click on “ “Action.”
  4. Go to “TOOLS” and click “Audio and Video Setting” and follow the instructions.
NOTE: You audio and video shoud work. Enjoy.

When done both the Audio and Video will function properly so you can chat and see family or friends you are connected to.
Hope this helps. Bud

Jan 11, 2009 | Microsoft LifeCam NX-6000 Webcam

1 Answer

Creative Cam Installation


Normal 0 Did you install the software with the camera connected to the computer? Disconnect the camera from the USB port and reinstall the software. When the program asks you to connect the camera, do so, and it should work. Hope this is of some help. Bud

Below is info for setting up Audio & Video to chat on line after you install , either Skype or a messenger program.


Web Camera’s have to be setup on the program they are to be used with. Just installing the camera on your computer does not set it up to broadcast on messengers or Skype.

Each program has Options that have to be setup in order for the Audio and Video to function properly.

A. Skype Setup:

After downloading and installing Skype set it up as follows:

  1. Go to TOOLS, then OPTIONS, and click on Audio Settings and set the Microphone and Speakers to the computer Audio Card.
  2. Then click on the Video Settings.
  3. The camera if installed properly will come up and show a picture.
  4. Then on the bottom of the page click on Save.

The camera and audio should function properly. Your friends and Family will now see and talk to you.

B. Yahoo Setup:

After downloading and installing Yahoo Messenger set it up as follows:

  1. Go to Messenger at the top left and click on it.
  2. Next go down to Preferences and click on it.
  3. Next Calling and Devices on the right and set the Microphone and Speakers to the computer Audio Card.
  4. Next go to the Test Audio section and (in blue writing) click on “Open the call setup assistant” and follow the instructions on the left window.

C. Windows Live Messenger:

  1. After you start Windows Live Messenger, expand the view by clicking on the square on top left next to the red X.
  2. Then on the Windows Live messenger window on the right side, click on “ “Show Menus.” And then click on “Show the Menu Bar”.
  3. Next go to the Menu Bar on right side, click on “ “Action.”
  4. Go to “TOOLS” and click “Audio and Video Setting” and follow the instructions.
NOTE: You audio and video shoud work. Enjoy.

When done both the Audio and Video will function properly so you can chat and see family or friends you are connected to.
Hope this helps. Bud

Jan 06, 2009 | Creative Labs WebCam Live!

2 Answers

A4tech viewcam pk635M


i want to connect my cam ..

Nov 21, 2008 | A4tech PK5

1 Answer

Lifecam VX-6000 will not install hardware.


Normal 0 To get the latest Microsoft Web Camera drivers, go to this site

http://www.microsoft.com/hardware/download/download.aspx?category=ICE

then select the necessary items as listed below, such as
  1. Select type of product. (Web cam)
  2. Select your product (camera model).
  3. Select your operating system. (XP, Vista etc.)
  4. Select your operating system langusge. (United States English)
Hope this helps. Bud

Jun 30, 2008 | Microsoft LifeCam VX-6000 (68C-00001)...

3 Answers

Webcam Installation problem


http://support.microsoft.com/ph/11859

Jan 10, 2008 | Microsoft LifeCam VX-3000 Web Camera

Not finding what you are looking for?
Microsoft LifeCam NX-6000 Webcam Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Webcams Experts

David Payne
David Payne

Level 3 Expert

13437 Answers

Brian Friend

Level 2 Expert

132 Answers

johncassells

Level 1 Expert

10 Answers

Are you a Microsoft Webcam Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...