Question about JVC RX-6020V Receiver

Open Question

My JVC reciever displays DSP MITCOM NG. What does this mean?

While this is flashing the amp is rendered useless.

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: JVC RX 6042

just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Posted on May 18, 2008

Ad
VOTIT
  • 2071 Answers

SOURCE: JVC A/V Receiver RX 7042S - DSP NG

it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Displaying....DSP NG can some one please help? some kind of error.


In my experience, NG on a system made in Japan means "No Good" (error). NG might stand for something else, but regardless, it sounds like an internal issue with the amp.

Sep 24, 2015 | Pioneer VSX-D510 Receiver

1 Answer

I spilled a liquid in my jvc rx-502ov receiver and a message reads dsp micom ng what do i do?


You fried the poor thing to put it mildly, Get a different one end cut down on your partying ,(GUY) Unless you have money to burn

Dec 05, 2012 | JVC Rx 5020v Stereo Receiver

1 Answer

Where is the microcomputer located in the jvc rx6030v?


Hello
The microcomputer, otherwise called as system control can be located on its main board. Some sets will have it on its front panel baord, along with the display unit board.

Feb 07, 2012 | JVC RX-6030V Receiver

1 Answer

I have a Pioneer VSX-D411 and there is dsp ng flashing, what is it


http://www.retrevo.com/support/Pioneer-VSX-D411-Receivers-manual/id/385ci976/t/2/

I believe it's trying to tell you something is wrong with its digital sound processing.

This was the best source I could find on it:
http://www.avforums.com/forums/av-amplifiers-receivers/381823-problem-pio-vsx811s-no-sound-display-says-dsp-ng.html


If you switch it to satereo / direct and the light goes out I'd say that would clinch it.

Jan 15, 2011 | Pioneer VSX-D411 Receiver

1 Answer

JVC RX-6042S shuts down after 5 seconds


It will be one of the transistors that regulate the lower volatges (5V, 12V...)
I ffixed mine. the heatsinking on those transistors is pathetic, and its no wonder they dont last.
Mine was the 5V circuit, which also supplies the DSP board. so if you are getting a DSP NG, that could be that as well.
Check Q1434 and Q1404. if one is faulty, it drags the other one down with it.
Good luck.

Dec 27, 2009 | JVC RX-6042 Receiver

2 Answers

The sound cut off for a few seconds when the reciever warm up


mine did this too, just before the dsp board went. start looking.

Jan 10, 2009 | JVC RX-6040 Receiver

1 Answer

Yamaha Dsp-A1000 5 ch amp Bought a used amp will be hooked to an awia reciever and speakers also have two subwoofers need help to install correctly witch connections to use


if you wanted to use your receiver as your controller and source then try to find out the receivber has got a bridge (jumper) between the pre-amp stage and the power amp stage. if your receiver does not have that, then you can just connect your receiver tape record out to one of your DSP inputs. subwoofers, the DSP has got a sub woofer out connector. you can use that (RCA type) to your sub woofers. put in series because DSP has got only one output for sub. or, you can connect your subs directly to the mains speakers, parallel connections. maybe one sub to your left and the other to your right channel.

Jul 24, 2008 | Yamaha DSP-A1000 5-Channel Amplifier

1 Answer

JVC A/V Receiver RX 7042S - DSP NG


it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Jul 03, 2008 | JVC RX-6042 Receiver

1 Answer

JVC RX 6042


just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Apr 02, 2008 | JVC RX-6042 Receiver

Not finding what you are looking for?
JVC RX-6020V Receiver Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

 Grubhead
Grubhead

Level 3 Expert

5158 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...