Question about Computer Monitors

Open Question

HP Monitor cycling through colors and is unresponsive to buttons

I have an HP VS19e LCD Monitor. I turned it on and the monitor going to sleep message came on, and then it started to cycle through colors one at a time and is no unresponsive to buttons. You said in another post to push the menu button, and then select the reset to factory setting option. My menu button, is unresponsive as well is there anything I can do to reset my monitor?

Posted by on

  • TechnoBabble Mar 30, 2009

    When the VGA cable is not connected the power button does nothing. When a VGA cable is connected, pressing any of the buttons brings up the monitor menu. The menu then automatically cycles through the options until it gets to the color options and then cycles continuously through the color options. Is there a reset for this issue?

×

6 Suggested Answers

  • 2 Answers

SOURCE: Reset back to factory defaults

To unlock the OSD

controls when the OSD is

preset to be locked, press

and hold the 'MENU'

button for 15 seconds to

enter the 'OSD Lock'

option and make
changes.

Nigel@netfishers

Posted on Oct 28, 2007

  • 238 Answers

SOURCE: Dell E173FP 17" LCD Monitor

hi, check out the micro switches on the monitor.. let me know..

Posted on Dec 15, 2007

SOURCE: HP vs19e flat panel monitor died

power supplybdown

Posted on Apr 04, 2008

Mark_Webber
  • 472 Answers

SOURCE: Going to Sleep

Due to the power surge, it is highly possible that the monitor was given a boot by your computer on it's way out.

This will short out a very small transistor inside the monitor on the video board and in turn, then monitor cannot see that there is a signal so goes to sleep.

If you get brave enough to venture inside the screen, then check near the cable input. The transistors are only around 3mm and have 3 legs (two one side and one in the middle on the other).

If you find anything like that burnt (get a magnifying glass) then replacing the board is the easiest option. Just don't be tempted to wipe the board before you look at everything very closely, you may wipe away the tiny bit of evidence you are looking for.

Hope it helps =)

Posted on Apr 09, 2008

  • 125 Answers

SOURCE: Reset Monitor back to factory spects.

Menu
Advanced
Factory Recall
Select
Select

(select must be pushed a second time to start the factory recall.

Posted on May 04, 2008

FoxSysTech
  • 23 Answers

SOURCE: input select button to switch between hdmi/dvi/vga

Unless there is simply some dirt or dust caught in it, I would imagine that the button has lost its 'spring' or bounce-back ability which means that either you can take the big risk of attempting to fix it or come up with some other clever way to give it bounce.

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My new L1940T (hp) monitor is stuck in sleep mode. At boot, green light illuminates, then goes orange. Window opens saying 'going to sleep mode' then completely unresponsive. Tried everything; moving and...


We need to narrow down to find out if it is your PC is not sending the video signal to the monitor or the monitor itself is bad, you need to try this monitor with another PC or try this PC with another monitor. Please post back what you find after trying the suggestions.<br /> <span style="FONT-SIZE: 10pt; FONT-FAMILY: 'Arial','sans-serif'; mso-bidi-font-size: 12.0pt"><a href="http://s807.photobucket.com/home/budm/allalbums">http://s807.photobucket.com/home/budm/allalbums</a></span><br /> <span style="FONT-SIZE: 10pt; FONT-FAMILY: 'Arial','sans-serif'; mso-bidi-font-size: 12.0pt"> </span><br /> <span style="FONT-SIZE: 10pt; FONT-FAMILY: 'Arial','sans-serif'"><a href="http://en.wikipedia.org/wiki/Capacitor_plague">http://en.wikipedia.org/wiki/Capacitor_plague</a></span><br />

Aug 26, 2010 | HP L1940T 19" LCD Monitor

2 Answers

Hp l2208w going sleep


Hi
I am sorry that the Monitor is going to sleep mode. Are you experiencing the same issue with different Tower or CPU? Turn OFF the monitor and power cycle it after a minute and check if the same issue persists. Also, reinstall the Video Driver.

Jul 16, 2010 | HP L2208W Monitor

1 Answer

My HP vs19e Monitor went black, when I turn it off...


guest, If monitor vs19e acts same when connected to different "known good" pc then try this site for info: http://www.lesliewong.us/blog/2005/05/02/hp-pavilion-f1703-flat-panel-display-blackout-solution/ How old is this model? When was last time it worked correctly? 12fixlouie

May 19, 2010 | HP Pavilion F1903 19" Flat Panel LCD...

2 Answers

HP vs19e monitor is blank. Power button is slowly


that is not a monitor problem that is a cpus problem disconnect the signsl cable and connect power cable you will see the post (power on self test) open the cpu draw the ram clean the dust and reinstall the problem will solved

Feb 26, 2010 | HP vs19 (Silver) 19" LCD Monitor

1 Answer

My moniter wentr out.


Hmm, haven't had experience with this exact monitor, but several people have had success with my tutorial on fixing the vs19d and vs19e. Check out the link below:

http://boredprojects.blogspot.com/2009/09/hpvs19e-monitor-fix.html

Sep 28, 2009 | HP Pavilion F1903 19" Flat Panel LCD...

2 Answers

Hp lcd f1532 h


This can happen if the minus button which happens to also be the auto image-adjust button is effectively grounded due to some internal fault or
if the switch itself has got jammed internally. In this case, if video signal is present, the motitor reproduces the image but continuously displays "adjusting" as osd message. If video signal is missing, the monitor cycles through solid colors in the black, red, green, blue, white sequence. I think this is part of the hp f1532 design to help the service
engineer( though I have not found any reference to it in official documentation yet). In this special case( minus button grounded), the
menu button is ignored by the monitor.

Kumar Talreja

Jul 26, 2009 | HP Pavilion F1523 15" LCD Monitor

1 Answer

My monitor is stuck in a constant color loop...


What you are seeing is a test they use at the factory. Here are the instructions to reset the monitor:

1. Press the MENU button
2. Use the + and - buttons to choose Advanced Menu
3. Press the SELECT button
4. Select Factory Reset
5. Select Yes
6. Press MENU again to remove the onscreen menu

Hope that helps :)

Dec 13, 2008 | HP Pavilion F1903 19" Flat Panel LCD...

1 Answer

Going to Sleep


got the same issue

hp pavilion 1723

Nov 01, 2007 | HP Pavilion F1903 19" Flat Panel LCD...

Not finding what you are looking for?
Computer Monitors Logo

Related Topics:

1,229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computer Monitors Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...