Question about Kenwood KSC-WD250 Car Subwoofer

Open Question

Kenwood diagram for ksc-wd250 - Kenwood KSC-WD250 Car Subwoofer

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: Wiring a Kenwood KSC-WD250 Subwoofer

7e83231.jpgi had the same problem Here is the diagram i used from someone else on fixya.  Thank you.

Posted on Jul 21, 2008

Ad
etirbynnor
  • 655 Answers

SOURCE: Installing self amplified sub to factory stereo

Hello Jax GS300,

Yes, you can use RCA cables. Just wire in a "low-level" converter.

Using RCA's is really the best way, allowing you to run shielded wiring to the sub, making it less likely that the wiring will pick up electrical interference. I'd install the converter on the rear speaker wires behind the dash.

If you do not want to convert the speaker output, you can drive the Kenwood directly from the speaker wires. The diagram in the install manual shows the connections coming off the rear speakers.

Here's a link to one output converter. This one will convert all 4 speakers.

http://www.crutchfield.com/p_142SLC4/Scosche-SLC4.html?search=level+converter

Hope this helps.

Posted on Apr 11, 2009

  • 32 Answers

SOURCE: how to disconnect Kenwood KSC-WD250 Powered

There should be RCA's power and ground connections. the rca's run behind the stero, the ground runs somewhere to the frame of the car and power runs to the positive post on the battery.

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenwood KSC-37 why does red light blink


In the manual, it states that if the LED is Blinking Red "The battery pack is defective or the battery pack contacts
are not properly mated with those of the charger" Below is a link to the manual.
http://www.buytwowayradios.com/products/resources/Kenwood/KSC-37-Owners-Manual-1.pdf

Apr 04, 2013 | Kenwood KSC-37 Replacement Charger for...

1 Answer

I have a kenwood ksc-wd250 subwoofer and the wire harness thats on the amp has 2 blk wires, 2 yellow, 1 blue w/white stripe, and 2 green and 2 purple wires. How do I wire this into my system. What color...


Sounds like thats for high end speakers.....should connect rca cable to the input and only other wires should be positive (b+) ground (negative) and remote (blue wire)

Mar 27, 2012 | Kenwood Car Audio & Video

1 Answer

How to disconnect Kenwood KSC-WD250 Powered Subwoofer from my car stereo


There should be RCA's power and ground connections. the rca's run behind the stero, the ground runs somewhere to the frame of the car and power runs to the positive post on the battery.

Jun 11, 2010 | Kenwood KSC-WD250 Car Subwoofer

1 Answer

How do you hook up a sub and amp to a stock radio with NO RCA outputs?


you can splice into the wires for your rear speakers and install some of your owns rca's and just use the low pass filter on your amplifier to eliminate the mids and highs from the frequency to your subs.

Jun 24, 2009 | Kenwood KSC-WD250 Car Subwoofer

1 Answer

Installing self amplified sub to factory stereo


Hello Jax GS300,

Yes, you can use RCA cables. Just wire in a "low-level" converter.

Using RCA's is really the best way, allowing you to run shielded wiring to the sub, making it less likely that the wiring will pick up electrical interference. I'd install the converter on the rear speaker wires behind the dash.

If you do not want to convert the speaker output, you can drive the Kenwood directly from the speaker wires. The diagram in the install manual shows the connections coming off the rear speakers.

Here's a link to one output converter. This one will convert all 4 speakers.

http://www.crutchfield.com/p_142SLC4/Scosche-SLC4.html?search=level+converter

Hope this helps.

Apr 09, 2009 | Kenwood KSC-WD250 Car Subwoofer

3 Answers

Wiring a Kenwood KSC-WD250 Subwoofer


7e83231.jpgi had the same problem Here is the diagram i used from someone else on fixya.  Thank you.

Nov 27, 2007 | Kenwood KSC-WD250 Car Subwoofer

1 Answer

Kenwood receiver/sub problem


The amp's remote turn-on wire is probably connected to the blue wire coming from the back of the stereo - this is intended for a power antenna, which is why it only works when listening to the radio. Disconnect it from the blue wire and connect it to the blue/white wire coming from the back of the receiver and you should be good to go.

Sep 21, 2007 | Kenwood KSC-WD250 Car Subwoofer

2 Answers

Ksc-wa100


Here is a picture to help you out.7e83231.jpg

Sep 01, 2007 | Kenwood KSC-WA100 Car Subwoofer

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4861 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...