Question about Kitchen Ranges

Open Question

Squeaking Thermador downdraft vent - Kitchen Ranges

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Mrvica
  • 167 Answers

SOURCE: Downdraft up and down

Hi,
this is ID 25898888.

Posted on Feb 22, 2008

Ad
alicantecoli
  • 22219 Answers

SOURCE: I have a 1989 model

check in the hood pipes for a rubber seal thats come adrift as something isloose or come apart allowing the hood to come too low so it passing the microswitch for the fan ,between teh tubes is a seal and suspect that one of these has collapsed allowing the hood to come down lower ,its a take it apart type job and see ?

Posted on Jan 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The vent downdraft keeps going up and down


Hello,

This means that one of the limit switches by the motor has failed.

Apr 22, 2011 | Thermador UCV36A 36" Universal Cook 'n'...

3 Answers

Thermador cooknvent downdraft CVS36R


this is the little circuit board in the switch that is defective here you will eed to replace it.

Oct 24, 2008 | Thermador UCV36A 36" Universal Cook 'n'...

1 Answer

Thermador cook n vent stuck in the up position. We have a thermador cook n vent. We had it running for about an hour. We turned the fan off but now it is stuck in the up position and will not go down. ...


replace the switch if the switch is going on and up position and not in down position the you should replace the switch for this part you can order it from thermador if they still stock the piece hope this helps

Aug 11, 2010 | Thermador UCV36A 36" Universal Cook 'n'...

1 Answer

Thermador Downdraft blower Fan Not Working


could have serveral problems / if under counter or in back of range . the last two i had the control buttons w wire harness needed replacement /another required the pc board in connevtion box ( under counter in right cornor. also look for poor connections in the power box .

Dec 07, 2009 | Thermador UCV36A 36" Universal Cook 'n'...

1 Answer

My thermador stove fan keeps going up and down cvs45r


no


Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Mar 07, 2009 | Thermador UCV36A 36" Universal Cook 'n'...

1 Answer

Cook 'n Vent Downdraft Up/Down Mechanism Replacing


just the switch should be replacable. My vent has a screw at each end (philips flatheads - accessible only when vent is up) just under the top cap. Removing the screws and cap should give you access to the switch. Just make sure you cut your breaker off first.

Nov 15, 2008 | Thermador UCV36A 36" Universal Cook 'n'...

1 Answer

Thermador cook top with down draft ventalation


I would think you can. Most of the cooktops are 240v and the vents are 120v, so the vent may be feeding off of one of the cooktop's hot wires. My vent is fed from it's own receptacle but is harnessed along with the cooktop's 240v.

Oct 31, 2008 | Thermador UCV36A 36" Universal Cook 'n'...

2 Answers

Install a Thermador UCV36 cook'n'vent


Hi schmidt_rich,

I'm Harvey the Master Plumber.

Your question is: You took over as owner builder when your builder "took the $ and ran". You are installing kitchen cabs now and discovered the PVC vent pipe (which goes into the foundation and out the side of the house) is in the wrong place for the location of the downdraft unit and integral blower. The vent is actually under the electrical connection panel. You were told initially( 2 yrs ago when you bought the downdraft cook'n'vent) there could be no bends in the exhaust fan route or it would change the effectiveness. Does anyone know if it is ok to put a bend in the connection to the vent? Or do you need to redo your kitchen cabinets?

I can syphathise. I have had to deal with this same problem. I have found that one ell will not degrade the effectiveness enough to notice. If you need more then you may need to adjust cabinets.

Feel free contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber

Sep 24, 2008 | Thermador UCV36A 36" Universal Cook 'n'...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Paul Carew

Level 3 Expert

2557 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...