Question about D-Link DP-301P+ Fast Ethernet Print Server (NTPRDLDP301P) Print Server

2 Answers

Setting up my D-Link DP-301P+ print server

I just bought a new D-Link Fast Ethernet Print Server DP-301P+ on eBay. It came with the manual, but there is no installation disk or software. Do I need any software or disk in order to set-up my new D-Link print server? Am I missing something? And if so, is there a website I can go to in order to download what I need to complete my install?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

All you need is a PC at same ip subset and use the browser to http://192.168.0.10 (the default). If not working, the ip may be changed. Connect it to a router that will assign a ip to the print server, and logon to the router to see which ip it assigned to it. Give router some time and refresh the list, then connect to that ip address.

Posted on Dec 01, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Print servers are typically controlled through a web interface, and do not need specific drivers. You can download the manual and installation guides here. You may need to change the default IP address; look at the section on Networking Basics in the manual.

Posted on Jan 13, 2009

2 Suggested Answers

  • 20 Answers

SOURCE: DP-301P+ Express EtherNetworkTM Fast Ethernet Print Server

You need to connect to it (using the broswer at the PC of same LAN with the current ip of the print server). Then click on Tools TAB, click on "Reset" at left. You should see "Do you want to restore this device to factory default setting?". Click on "Apply"

Posted on Dec 01, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have connected the d-link to a KOT printer,my network cannot find the server.And according to the manual I cannot browse the default ip of the DP-301P+ sever.please assist me immediately.


I have D link DP- 301P Print server I am using it in Epson M188D Printer for KOT Printing but its shows some times printer not found on network, please help me to solve the problem.
Ajay

Mar 22, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I have print server DP-301U Pls let me know the default IP address for configuration


Hi
As far as I can remember the default IP is 192.168.0 .10, subnet 255.255.255.0
If this isn't the correct IP address, you'll need to reset the d-link print server Hope this helps
Regards, c0d3

Feb 09, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

Hi sir how can i change ip address for Dlink printer server DP-301P+


Hi,
Logon to the Print Server web configuration and begin managing the DP-301P+, simply launch the browser (e.g. Internet Explorer) and type dlink-xxxxxx, where xxxxxx are the last six digits of DP-301P+'s MAC address. The MAC address can be found on the bottom side of
the DP-301P+ device.

creativetech_19.jpg

Default IP Address of DP-301P+ is set as automatically getting from DHCP server or Router with build-in DHCP server. Please note that the PC's IP Address must be in the same subnet as the print server's IP Address for the two devices to communicate. (For example, if print server's IP
Address is 192.168.0.10, with a subnet mask of 255.255.255.0, then your computer's IP Address should be 192.168.0.x, where x is a value between 1-254, excluding 10.)
For additional information, please refer to Dlink printer server DP-301P+ Product Manual

Let me know if any further clarification/ assistance is required.

Good Luck!
Appreciate generously, if the solution could have been of any help!
CreativeTECH

Jan 11, 2011 | D-Link DP 301P (DP-301P) Print Server

2 Answers

How to reset the administrator password of the D-Link DP-301P+


hi
i forgot password Printer Server D_link Dp-301p
Please Help Me

Jul 30, 2009 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I would know if D-Link DP 301P Print Server supports SNMP protocol because i need to print from IBM iseries thank you


It supports all below protocol so you can give print from IBM iseries .

TCP/IP Protocols Supported :
  • BOOTP
  • SNMP
  • Telnet
  • TFTP
  • FTP
  • LPD
  • RARP
  • DHCP

Jul 28, 2009 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I forgtten the IP of the Print Server D-Link 300U. Please tell me , that how to reset the IP


usually by resetting it. pushing the reset button on the back it (tiny hole on the back) for 30 seconds, while plugged in to power,

Jun 15, 2009 | D-Link DP 301P (DP-301P) Print Server

1 Answer

DP-301P+ Express EtherNetworkTM Fast Ethernet Print Server


You need to connect to it (using the broswer at the PC of same LAN with the current ip of the print server). Then click on Tools TAB, click on "Reset" at left. You should see "Do you want to restore this device to factory default setting?". Click on "Apply"

Jun 04, 2008 | D-Link DP 301P (DP-301P) Print Server

1 Answer

Forgotted the Ip of D-Link DP 300U print server


You may use the PSAdmin software to configure your print server even if you don't know the IP address. The only requirement is that the DP-300U has to be in the same network (subnet) as your PC running PSAdmin. In the PSAdmin, you will then be able to view or change the IP address.

Here is the link to download PSAdmin:
http://support.dlink.com/products/view.asp?productid=DP%2D300U#apps

Remember that if you also have forgotten the Admin password, you will have to ship the unit to D-Link in order to have it factory reset.

May 10, 2008 | D-Link DP 301P (DP-301P) Print Server

1 Answer

No printing threw terminal service


do you have the options set correctly on the remote computers assistant to use local devices

Dec 25, 2007 | D-Link DP 301P (DP-301P) Print Server

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

2,968 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2259 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18330 Answers

Mike

Level 3 Expert

4332 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...