Question about Kitchen Ranges

1 Answer

I was trying to use self cleaning feature on Whirlpool electric range . After 20 mins it stopped with error message F5E0. What does that mean

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Kitchen Ranges Master
  • 2,651 Answers

F5 - E0 F5 - E1 and E2 Check door/latch switch Replace switch if defective

Posted on Jan 11, 2009

  • rpaint01 Nov 13, 2010

    I have a Kenmore 95115102 and all I did was manually cycle the door latch a few times. It's at the top of the chassis when the door is open.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I get an error message F9-4 when I try to use the self-cleaning feature.


check for obstruction in the door closeing latch/switch
f9-4 on a maytag means i cant close/lock door

Jan 29, 2010 | Maytag MER6772 Gemini Electric Kitchen...

2 Answers

I am getting an F5E0 messaging when trying to do the self clean any idea what this is


it means that your switch on the lock is stuck in the wrong postion literally just fixed mine....lift up the heating elements of top and remove the 8 or so screws that are around the perimeter of the and it reveals the lock switch, myself i just kind of pushed on it to get it to go back haha...i pushed the lock part towards the left side and it slowly moved back on its own....
Hope This Helps you!!!

Dec 12, 2009 | Whirlpool RF368LXKS Electric Kitchen Range

1 Answer

Oven door will not release after cleaning


Try waiting until the oven is COOL, then switch the power off to it , wait 20 seconds and switch the power back on?

Jul 29, 2009 | Whirlpool GR460 Electric Kitchen Range

2 Answers

How do I stop and open door in the self cleaning?I have a hugh mess in the oven I clean the extra stuff on the bottom what happens if it starts fire and I can not shut off and open the door.


Large spots should be cleaned BEFORE starting self clean..The self clean can not be "paused" and continued..It has to be shut down and re started..

Jul 16, 2009 | Whirlpool Accubake RF362LXTT Electric...

1 Answer

Stop self-cleaning


Reset the curcuit board by pulling the plug for 10 min. This will reboot the board and force it out of the self clean mode.

Apr 30, 2009 | Kitchen Ranges

1 Answer

Tried to selfclean my NEW oven but get error message F5E1


Reading all the questions and responses - I had the same problem (would press "self clean", it would run for less then a minute then give the error message), so once I saw the code was E5F1 and what it meant (thanks for whoever posted that), I just pressed on the door for the first minute of the cycle, and self-cleaning then worked. Go figure :)

Jan 06, 2009 | Whirlpool RF378 Electric Kitchen Range

1 Answer

My oven flased an F9 error....


The solution to this issue is to finish running the self cleaning feature to this oven, Shutting off the oven or opening the door before the self cleaning feature has completely run will send a F9 error from the safety co0ntrol unit feature built in to the system bios of the control circuit, You will need to close the oven and set the option self cleaning to run now. if your error message prevents you from taking these steps you will need to unplug the oven from the wall socket and let it sit for an hour to reset the screen and then run the self cleaning feature all the way trough, it will shut down on its own when the self cleaning cycle has completed

Oct 24, 2008 | Frigidaire FEF366 Electric Kitchen Range

3 Answers

Whilrpool Self Cleaning Range Door won't unlock


try this 1. Verify error code by pressing and holding CANCEL/OFF key for 5 seconds.
Momentarily (less than 5 sec.) press CANCEL key again to remove error code
display.
2. Press and hold any key for 1 minute until F2 E0 code is displayed.
3. Cancel F2 E0 error code.
4. Program and start the clean mode. Observe to see if door locks. If it does not,
inspect the locking mechanism from the solenoid to the latch pawl and door to
find the cause of the problem. If the door is not locking, then 1 minute from the
start of clean, the F5 E1 code will again be displayed. Steps 1 through 3 will
have to be repeated before another clean can be started.
5. Once any mechanical problems with the latch mechanism have been corrected,
program and start a clean cycle (after, if necessary, clearing F5 E1 error code)
to ensure proper operation of the door lock. Immediately cancel the clean mode to observe proper operation of door unlock

Feb 10, 2008 | Kitchen Ranges

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

744 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...