Question about Projection Televisions

1 Answer

When we finished watching a DVD and switched back to TV, the Denon AVR 2807 receiver would not produce any sound. We tried following the manual directions for function and input mode but no luck. Help!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Our expert solved the problem for me. I did not realize it until I turned off TV and turned it on the next morning and the sequence he told us to follow had worked! Sound restored. He was wonderful and patient. Thanks.

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I transfered from watching my sattelite tv to watching a dvd using the tv control. The dvd sound worked ok, but I couldn't get a pictue. Then I tried to watch tv again, but the vidio would not come in,...


Just in case, here's the 108-page user's manual for your TV:
http://www.hdtvsolutions.com/pdf/MIT_WD-52525_WD-62525_WD-52725_WD-62725_Manual.pdf

Yor "NetCommand" TV remote is a wondrous thing, capable of throwing off anyone.

When the 'Device Selection Menu" is dispayed, and only when the device icon is highlighted,
does the key work, and it also only works when the remote is in "A/V Receiver" mode -
not in "CABLE or DBS" mode, nor "VCR" mode, nor "DVD" mode.
So, (1) set the NetCommand remote to "A/V Receiver" mode
(2) bring up the Device Selection Menu, using the key on the remote
(3) highlight the Satellite receiver input icon (highlighted with a Yellow outline)
(4) press GUIDE on the remote, to swap the analog digital setting.

Also displays ChannelView for Antenna 1 and Antenna 2 - you may have accidentally
set the TV to get its input from the wrong Antenna.

If your TV has lost memory of its DBS source, you may have to re-teach the TV (using the remote)
that the DBS (Digital Broadcast Satellite) input exists, and to which input its connected.
Refer to "Edit NetCommand, Add an A/V Receiver", pages 39-45 of your Owner's Manual.

Jan 31, 2011 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Picture but no volume


I went to menu then press net command and press audio then enter. Then I press the arrow up on the adjust key and switch it from AVR to TV/Video.

Jan 06, 2010 | Mitsubishi WD-65731 65" HDTV

1 Answer

Can not change "Device" input, no sound control,no remote control


I unplugged the manual switch electrical connection. Everything works just fine with the remote.
Not sure what is wrong with the switches just yet, but suspect a resistor problem. I have checked all voltages and have 5.04 v feeding the switch assembly on what I feel are the correct circuits
(5v, ksco, ksc1, man/reset). I have no voltage on the ground circuit with the board plugged in, so the ground circuit should be ok. I have tested all switches with ohmmeter, all switches work. I suspect a resistor problem as I have one with no voltage drop and one resistor with no voltage pass-thru. Would need a wiring schematic with values to pinpoint better.

May 16, 2009 | Mitsubishi WS-65711 65" Rear Projection...

1 Answer

We have sound but no picture i have sound but no picture. when you change inputs the word input is doubled up and distorted


There were not much info in the manual but it did suggest trying this.
1st- Unplug for a few minutes and then plug it back in. Or use the reset button look it up in the manual. MANUAL

2nd- Blank screen troubleshooting

• If you're trying to watch TV, change channels or press the ANTENNA button to switch tuners.
• If you're trying to watch something that's playing on a component connected to the TV (like a DVD or a VCR tape), press the TV
button on the remote, then press INPUT until you get to the correct video input channel.
• If you're trying to watch a component (like your DVD player or VCR), make sure the component connected to the TV is turned on.
• If you're trying to watch a component (like your DVD player or VCR), make sure the component is connected correctly.

Post back if non of these ideas work and explain if there are any lights flashing or changing colors on the front where the green light usually is. A fixya rating would be appreciated, thank you for stopping by Fixya!

Feb 16, 2009 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Tv hums when hdmi is connected via dvd player


how do you have the audio hooked up for it if you are using componet cable (red,white) for sound they could be causing the humming you can either switch audio cables or use some other form of cable for sound

Jan 24, 2009 | Samsung HLN617W 61" Rear Projection HDTV

3 Answers

We have a Denon AVR 4306 Surround Sound Receiver connected to a Motorola HDMI dual tuner DCT 6416 PVR. We're using component video cables to relay the video signal and RCA cables for the audio signal. We...


Try checking first the connection for the audio, then make sure the surround sound receviver is also connected properly and also turn everything OFF then turn back ON since you have a disruption just to refersh all devices and check it again if there will be sound already..

Hope that helps..........

Jun 22, 2008 | Projection Televisions

1 Answer

I have a Denon AVR-3300. I am getting picture but no sound in the TV/DBS mode. Every other connection is working fine.


Try switching one of the working source connections to the TV/DBS connection. Also note that TV and DBS are actually separate inputs on some models.

Apr 05, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...