Question about Toshiba 62HMX84 62" Rear Projection HDTV

1 Answer

Blinking red and green lights no image. I've replaced the lamp

And it worked that night when we tried to turn it on both green and red lights started flashing and now has no image.
Can some one tell how to fix this problem?
Thank you very much for any assistance this issue!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 441 Answers

You might have the lamp in wrong, it should have a metal clip on both sides, one of them is probably bent. If you bend it back it should start right up

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Red/green lights both blink and tv will on turn on


Are the red and green lights blinking at the same rate or not? If the green light is blinking every 3 seconds and the red light is blinking every 1/2 second, the lamp door is not properly secured. If both lights are blinking at 1 second intervals, try replacing the lamp. If a new lamp doesn't solve the problem, the TV needs service.

I hope this helps.

Cindy Wells

Jun 23, 2011 | Toshiba 52HM95 52" HDTV Projection...

1 Answer

Replaced bulb yesterday worked fine. Today light will not turn on. projector turns on both lights green for 10 seconds, then power goes red and status blinks green for about 5 seconds, then status light...


green green is power on, normal
then it tries to light the lamp, but it can't so the protection circuit comes activated.
you get red and green blinking

Then it goes to standby, red and off.

so something has happened to the lamp, or lamp ballast power supply.
Take the lamp out and check if all is OK with the 2 terminals in the connector, and the leads to the lamp are intact.

Failing that, I would suspect the ballast lamp power unit

Mar 25, 2011 | Mitsubishi HC1600 Projector

3 Answers

Tv won't turn on. It blinks green then red.


Hi,
Question shows tv is Sony KDF-60WF655.
Green light blinks when tv gets prepare to fire up lamp, check internal circuits then show picture on front screen.
Red light blinking shows some kind of internal problem during circuit check and protection got activated upon some failure.
Count the red light blink as you will see 3 second long pause and post it here to diagnose what section of tv got problem.
Did you replaced its lamp in last 2-3 years?
Thanks.

Jun 01, 2010 | Sony Grand WEGA KDF-60WF655 60" Rear...

2 Answers

SONY KDF-E55A20 5 red blinking lights on power button


Hi,
Symptom shows Lamp is weak in result and causing restart of TV again and again. Your TV requires new lamp as per following part number...
A1085447A* LAMP BLOCK ASSY XL-2200U
It is available in Sony Accessories Store for $200 and replacement procedure is written in instruction manual of TV.

Always buy Sony original lamp for TV and avoid aftermarket / cheap lamp for TV safety.

May 18, 2009 | Sony KV-36FV26 TV

1 Answer

Alternating power and lamp status lights


...replace the lamp. The lamp is most likely WAYYYYY past its prime so I suggest starting there. Sometimes even if you had just replaced the lamp the new lamp could've blown. When there is no signal running through the lamp circuit there is no signal to the display sensor, which means no image.

hope this helps!

Jan 28, 2009 | Mitsubishi XD300U Multimedia Projector

1 Answer

Toshiba dlp red light green light on and off no image


It was the lamp cover original response was right on point

Nov 29, 2008 | Televison & Video

1 Answer

Sony Wega KDF-55E2000 won't turn on


A 5 blink code is a lamp power supply problem, but I would try a new lamp. I'd say about 90% of the time that fixes the problem.Get an ORIGINAL Sony lamp as the aftermarket replacements are ****. If you replace the lamp and still have the problem, you will need to have the lamp power supply/lamp ballast replaced

Oct 19, 2008 | Sony Grand WEGA KDF55E2000 55" Projection...

1 Answer

XG-C50 Problem


Hello

Replace the fly-eye lens of projector.

Viren

Nov 09, 2006 | Sharp (BQCXGC50X1) Projector Lamp for...

Not finding what you are looking for?
Toshiba 62HMX84 62" Rear Projection HDTV Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

70983 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jaime Hernandez

Level 3 Expert

2270 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...