Question about Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Kenmore he4t washer codes

Stopped mid cycl shows PF code. controls seem locked up at this time

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kenmore Master
  • 9,472 Answers

The control for the washer likely detected a problem. The failure code will not be displayed on all models of washers. You can recall the error code by using this procedure:

  1. Select the "Drain/Spin" cycle.
  2. Select No Spin.
  3. Press the "Prewash" options and hold this button for 5 seconds.
  • Immediately after those 5 seconds the last stored failure code is displayed for 4 seconds.
  • After those 4 seconds the display switches automatically back to the selection mode
NOTE: If your washer does not have the Pre-Wash option. Then use the 2nd Rinse button (called Extra Rinse). The failure code should stay in the memory so that it can be recalled as often as necessary and as long as it is the youngest failure Code.

Posted on Nov 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 91 Answers

SOURCE: Kenmore Elite HE4t Washer Control lock lit, door locked

121 MINUTES USUALLY DRAIN CYCLE PLZ REMOVE 3 BOTTOM PANEL SCREWS 7 MM SCREWS, TO OPEN DOOR SLIDE RIGHT HAND TOWARDS DOOR LOCK ,THERE WILL BE A SMALL LEVER TOO PULL DOWN ,NOW ITS OPEN,,, SINCE U HAVE BOTTOM PANEL OFF PUMP IS RIGHT IN FRONT REMOVE PLASTIC HOUSING CLOCKWISE ,,,REMEMEBER HOLD 3 GALLONS OF WATER STILL ,HAVE BUCKET READY ,NOW CLEAN OUT PUMP AND DEBRIS ,, CLOSE IT UP SHOULD BE FINE NO MORE PROBLEMS ,,,,,

Posted on Jan 02, 2009

  • 1294 Answers

SOURCE: Kenmore Elite HE4t Washer - "Control Locked"

Press and hold 'dry' & 'spin', shd unlock OR
Try holding the "end of cycle" button down for 5 or 6 seconds. You must hv done it accidently, it is the child lock device. Pl. rate if helped.

Posted on Jan 02, 2008

  • 1 Answer

SOURCE: Kenmore HE4t Won't continue drain cycle Code F6 & beeping

Take off the bottom panel (unplug unit first!) and unscrew the cap on the drain cylinder, be sure to have plenty of towels to soak up the water! pull out the center piece and check out all the treasures stored inside. Be sure to use a flashlight and lift up the black hose behind it to get any leftovers in the hose. I just did it today and could not believe how much stuff was in there...coins. pens, buttons, lost of wet lint had it clogged. The clothes finally don't smell!

Posted on Apr 19, 2009

localwonder
  • 6784 Answers

SOURCE: what do these error codes mean?

FH

No water detected entering machine or pressure switch trip not detected

If after 30 seconds the control does not detect water entering machine, the valves will be turned off and the error code will be displayed.
OR
If the control has turned the water valves on, and after 8 minutes, the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off, and the error code will flash.

Press PAUSE/CANCEL twice to clear the display.

Possible Causes / Procedure

• If there is no water in the unit:
- Make sure that both valves at the water source(s) are turned on all the way.
- Check for plugged or kinked inlet hoses or plugged screens in the inlet valves.
- Verify inlet valve operation.

• If there is water in the unit:
- Verify drain pump operation.
- Verify that the pressure switch hose is in good condition and properly connected to tub
and pressure switch.

1. Verify there is not a siphon problem.
2. Unplug washer or disconnect power.
3. Verify wire harness connections to inlet valves, pressure switch, drain pump, flow meter,
and Central Control Unit (CCU).
4. Check all hoses for possible leaks.
5. Plug in washer or reconnect power.
6. Verify pressure switch operation.
7. Verify flow meter operation by blowing air through the part and measuring the resistance.
8. Verify CCU operation by running a Diagnostic test or any cycle.

Replace failed component.(usually this will be failed pressure switch. the hose should be replaced as well)

Posted on Jul 21, 2009

pride applia
  • 232 Answers

SOURCE: Kenmore Elite quietpak9 HE4T washer FH error code

go 2 repair clinic on line, same codes for whirlpool duet repair help then error code tab

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair HE4t with HF code?


HE4T had problem on control board when early time version. Later they modified control board and find new version should fix your problem.

Apr 24, 2014 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

2 Answers

My kenmore elite smartwash/he4t


The "F11" fault code will display if the Motor Control Unit (MCU) has an internal failure; repeating under or over voltage, or over current conditions. If failure occurs during high speed spin the door unlocks after 3 minutes. The MCU (Motor Control Unit) is located beside the motor. Here is the part to order.

Dec 02, 2012 | Kenmore Elite 45986 Front Load Washer

2 Answers

Error message of f dl on kenmore washer model he 4t


does your washer stop on spin cycle some time. your is 4/5 years old?. f dl means door lock system is bad but i don't think so. do you have other error code beside f dl if yes then i think your washer need new main control board.

May 24, 2009 | Kenmore HE4t 3.8 Cu. Ft. King Size...

1 Answer

Washer stops with F11 code; door won't open


F-11 ERROR CODE MEANS :

Serial Communication Error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

TO RESOLVE THE PROBLEM:


  • Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)

  • Check the Drive system for any worn or failed components

  • Check MCU

  • Check CCU

  • Check Motor

  • Check Wire Harness


May 05, 2009 | Washing Machines

1 Answer

Washer stops washing and gives a p5 trouble code


PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Press and HOLD start to continue the cycle, or press off/pause to clear display.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 12, 2009 | Kenmore Elite 45986 Front Load Washer

3 Answers

Kenmore Elite HE4t washer won't spin


The motor controller board is likely bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 06, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore he4t washer shows f-11 error


F-11 // WILL THEN APPEAR FDL CODE DOOR LOCK LOCK FAILURE, F-11 COMMUNICATION ERROR REPLACE MAIN CONTROL,, JUST REPL 3 TODAY ....

Nov 28, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

F Code for the Kenmore Elite he4t Front Load Washer (3 years old)


Hi! ricksmith
What is the first three digits of the model number.
The he4t I have reference to does not have a "F" code error. Most of the codes are two digit, PF, F1 to F9 etc.
You could try: Pressing Pause/Cancel two times to clear code. As well as unplug for 20 seconds. Do you have power fluctuations in your area.
InMrFixIt

Aug 27, 2008 | Kenmore Elite HE4 Electric Dryer

4 Answers

Kenmore Elite HE4t Washer - "Control Locked"


Press and hold 'dry' & 'spin', shd unlock OR
Try holding the "end of cycle" button down for 5 or 6 seconds. You must hv done it accidently, it is the child lock device. Pl. rate if helped.

Dec 29, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore 3.8 cu. ft. HE4t Front Load Washer Logo

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2128 Answers

fordexpert

Level 3 Expert

5501 Answers

Mike Carew

Level 3 Expert

969 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...