Question about Kenmore Dryers

1 Answer

Kemore dryer need a picture of part placements

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 8,220 Answers

Posted on Nov 29, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kemore series 90 dryer model number 110.60922990 with a non removeable back and I am trying to change the heating element...I dont see any way to get at the element..the back doesnt come off and...


The bottom panel will come off after releasing the tabs between the lower panel and the front panel. Once the lower panel is removed, you will have access to the heating element. The link below will take you to a breakdown picture of your dryer.

Picture

Kelly

Mar 22, 2011 | Dryers

1 Answer

My Kemore stackable dryer does not work properly. I have to run the dryer 3 or 4 times to dry a load. Does feel hot at times when I open the dryer and feel the clothes.


Perhaps you have an air restriction of some sort. Cleaning the dryer and checking the vent can greatly increase efficiency. I recently replaced the glides and belt on one of these and made some repair photos. The dryer was plum full of lint all over the controls and everywhere. I took a shop vac to it before I snapped the pictures later that day. I have included a manual also HERE.

Dec 27, 2010 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Dryer does not heat


Hello,
Check out this tip it will help you with your problem...

http://www.fixya.com/support/r4398592-gas_dryer_not_working_gas_dryer_not

Heatman101

Mar 23, 2010 | Kenmore 72972 Gas Dryer

1 Answer

Kemore Stackable Washer Dryer No Heat.


I think you need to look at the heating coil to see if it is open circuit, either visually or test with OHMmeter.

Jan 23, 2010 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

I replced ingnitor in my kemore gas dryer but not flame


Hello Friend, If the igniter is glowing continally and not clicking off, then your therm-disc is definately bad. It's attached to the burner shroud right across from the igniter. It reads the heat off the igniter through a little rectangular hole in the shroud. Replace and problem should be solved.

If igniter is glowing and then cools down and then begins to glow again in a repeating manner then I would say that the thermo-disc is good and you need to replace the gas valve coils. coils are easy to change, they are located on top of gas valve, two screws hold them in place. An easy fix.

Happy to help, Tim.

Jun 30, 2009 | Kenmore 75944 Gas Dryer

2 Answers

My kemore dryer model 11071812001 not drying clothes


Sounds like the problem is the solenoid coils on your gas valve. easy to replace and inexpensive + common. their are 2 coils on the valve that have 2 wires each going to them. Let me know if you have any other questions,
Phil

Jun 10, 2009 | Kenmore 73952 Gas Dryer

1 Answer

Kemore dryer (Mod#110.66512694) stops running


Reach inside and turn the drum. If it is hard to turn then something may be causing the motor to get hot and quit on overload. An overload is wired into each motor to prevent the copper from melting. If the drum is hard to turn you might want to inspect the rollers and idler. ACCESSING YOUR MACHINE

May 16, 2009 | Dryers

1 Answer

Kemore he3 dryer error code E1


Hey fookie you need a thermistor for that dryer. It runs with no heat ?..Let me get a pic for you it is about 25 bucks oh and is part 42 on the pic below

ndna7hpl.png

Oct 23, 2008 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2287 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...