Question about RCA RCU410MS Remote Control

1 Answer

Remote stopped working....

For some reason my remote stopped working. I have changed the batteries, reprogrammed the codes, the lite still comes on when the buttons are pressed but none of the buttons work. Any ideas?

Posted by on

  • Sandra Beekhof Jun 06, 2007

    didn't work, looks like i'll have to get a new remote, very strange though...
    thanks.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,985 Answers

The buttons on most remotes are in fact a silicone rubber sheet with a conductive blob in the centre of the buttons that makes with the printed circuit board. Dismantle the remote with care - a small screw near the battery compartment and the 2 halves of the shell snapped together.A thin blade to prize it apart starting near the battery end. Lift the rubber sheet of buttons and gently wipe the underside with a piece cotton wool soaked in detergent water and squeezed dry- or if you have them a 'Moist Wipe Tissue' Do the same with the circuit board. Make sure they are absolutely dry before re assembly. Before you re assemble you will see the underside of the circuit board- plain plastic no circuits probably rests on pillars in the bottom shell. A thin piece of card may improve the contact between board and button sheet.

Posted on Jun 06, 2007

  • john ash
    john ash Jun 06, 2007

    just for the record- when you took it apart
    what did you find?
    Was it all any different from my description?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My remote stopped working I need to know how to reprogram it and what is the code thank you


If its the one that came with the TV just change the battery or batteries. If not what is the model numbers of the TV and remote.

Aug 05, 2011 | Sanyo Televison & Video

1 Answer

My remote control simply stopped working altogether. I changed batteries 3 times(and verified the batteries were good). The dvd/vcr controls on the player itself function properly. I cleaned the remote...


If it is a universal remote not branded to the tv and the batteries went dead or are out for too long then the remote lost the codes and needs to be reprogramed!

Mar 15, 2010 | Sony RMTV501A Remote Control

1 Answer

Chamberlain remote has stopped working, new


WHEN YOU CHANGE THE BATTERY NO NEED TO REPROGRAM THE REMOTE.
THE FLASHING LIGHT TELLS YOU IT IS SENDING A SIGNAL THAT IS BEING RECIEVED IT IS JUST NOT THE CORRECT CODE TO OPEN THE DOOR.
REPROGRAMING THE REMOTE SHOULD SOLVE THE PROBLEM

HOPE THIS HELPS

Sep 28, 2009 | Chamberlain Powerdrive PD422D 1/2 HP...

1 Answer

Toyota 2000 Landcruiser Pardo remote need to reprogram


forgive my poor english/do U have a challanger alarm in Your car?If U have U must programm Your pilot in service because challenger has a radio device to programing pilot to the system

May 17, 2009 | 2000 Toyota Land Cruiser

1 Answer

Remote door entry not working


could be that the remote lost memory during battery change may need to reprogram

Apr 28, 2009 | 2000 Toyota Land Cruiser

1 Answer

I have a car fitted with a Clifford GS 470 alarm but I cant get the alarm to stop. The car that this alarm was fitted in has not been started in 5 months and so the battery ran flat. I replaced the battery...


you might have to replace the batteries in the remotes. The reason why the alarm is going off because once you plug power back to the alarm brain it sets the alarm off and the only way to make it stop is to hit the unlock button the remote. Make sure all connections on the alarm brain are good and try changing the batteries in the remotes. also might have to reprogram the remotes to the brain if it has been sitting for awhile.

Feb 16, 2009 | Vehicle Parts & Accessories

2 Answers

RCA Universal Remote stopped working


I have the same problem on my RCA UNIVERSAL remote too..any one could me ?

thanks

Jan 08, 2008 | RCA 244889 Remote Control

2 Answers

Volume and mute buttons suddenly stopped working


Try changing the batteries. Most times the "tivo" buttons will work but the "tv" buttons will stop working when the batteries are low.

If you have done that, go back into settings and program the remote again for your tv, then give it a shot.

Nov 05, 2007 | Tivo DirectTV Remote Remote Control

Not finding what you are looking for?
RCA RCU410MS Remote Control Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76001 Answers

jason

Level 3 Expert

905 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...