Question about York Yankees Bedding MLB Comforter

10 Answers

York pkg unit

I need the blinking codes for york pkg unit m# D2GA036N08006C

Posted by on

10 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 108 Answers

Hello res1bnoq,

According the the York installation instructions these are the diagnostic LED blink codes for the control PC board:
OFF - normal operation
ON - board failure
1 flash - ignition attempts or recycles
2 flashes - compressor low pressure switch open
3 flashes - compressor high pressure switch open
4 flashes - flue inducer cetrifugal switch open (fault) or closed (fault)
5 flashes - flame rollout switch open
6 flashes - furnace high limit switch open
7 flashes - (optional) heating mode 1 hour waiting period for auto reset from flame failure lockout

Hope this helps you out.

Posted on Jan 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

This link may be also usefull

Posted on Jan 17, 2009

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

2 flashes - compressor low pressure switch open
3 flashes - compressor high pressure switch open
4 flashes - flue inducer cetrifugal switch open (fault) or closed (fault)
5 flashes - flame rollout switch open
6 flashes - furnace high limit switch open
7 flashes - (optional) heating mode 1 hour waiting period for auto reset from flame failure lockout

Posted on Jan 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,239 Answers

Hi According the the York installation instructions these are the diagnostic LED blink codes for the control PC board:
OFF - normal operation
ON - board failure
1 flash - ignition attempts or recycles
2 flashes - compressor low pressure switch open
3 flashes - compressor high pressure switch open
4 flashes - flue inducer cetrifugal switch open (fault) or closed (fault)
5 flashes - flame rollout switch open
6 flashes - furnace high limit switch open
7 flashes - (optional) heating mode 1 hour waiting period for auto reset from flame failure lockout

 When the unit gets into this blowing only cold state, the LED is blinking 8 flashes. There is no 8 flashes on the list. 

if thats the case.Then again, sometimes after reseting the unit with the fuse block it will start to work properly for another 4 - 6 - 10 hours. Sometimes a day or so.

The circuit board is a Robertshaw 100-825-04 which a Google search says is now obsolete so I can't find any documentation on it. Also it appears that Robertshaw is not even in the HVAC control board business any more.

Posted on Jan 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 470 Answers

Pls choose this code get from my book  025-29084-700, 401T-CARL39410, 401 0442, CAR02529084700

Posted on Jan 10, 2009

  • 1 more comment 
  • Antonio Buenafe Jr.
    Antonio Buenafe Jr. Jan 18, 2009

    According the the York installation instructions these are the diagnostic LED blink codes for the control PC board:

    OFF - normal operation

    ON - board failure

    1 flash - ignition attempts or recycles

    2 flashes - compressor low pressure switch open

    3 flashes - compressor high pressure switch open

    4 flashes - flue inducer cetrifugal switch open (fault) or closed (fault)

    5 flashes - flame rollout switch open

    6 flashes - furnace high limit switch open

    7 flashes - (optional) heating mode 1 hour waiting period for auto reset from flame failure lockout



  • Antonio Buenafe Jr.
    Antonio Buenafe Jr. Jan 18, 2009

    thats the code my dear,, but make sure you have 100% compatible on it,, choose the best

  • Antonio Buenafe Jr.
    Antonio Buenafe Jr. Jan 22, 2009

    (1):Trane 7 1/2 ton heat pump - Antonetz
    Re(2):Trane 7 1/2 ton heat pump - pricera
    Re(3):Trane 7 1/2 ton heat pump - Antonetz
    Re(4):Trane 7 1/2 ton heat pump - pricera

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers

Hi!
You can find the codes usually on the back of the blower access door OR the burner service door.

Thanks
Rylee

Posted on Jan 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 431 Answers

Try calling them. Its quite difficult to get the b codes for this.

Posted on Jan 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

That board is no longe made. Getting the codes is a daunting task!

Try calling York in Pa. they must have a technical department that can assist you. 1-800-910-YORK

Certainly have the model and serial number when you call... or try their website.

www.yorkupg.com

Of note York was bought out recently by Johnson Control.

Posted on Jan 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 326 Answers

According the the York installation instructions these are the diagnostic LED blink codes for the control PC board:
OFF - normal operation
ON - board failure
1 flash - ignition attempts or recycles
2 flashes - compressor low pressure switch open
3 flashes - compressor high pressure switch open
4 flashes - flue inducer cetrifugal switch open (fault) or closed (fault)
5 flashes - flame rollout switch open
6 flashes - furnace high limit switch open
7 flashes - (optional) heating mode 1 hour waiting period for auto reset from flame failure lockout

Posted on Jan 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Just curious what is it doing .... and i know it's not bedding... what type of unit is it ?

Posted on Jan 10, 2009

  • Roberta Smith
    Roberta Smith Jan 10, 2009

    2 blinks=high head pressure
    3 blinks=high discharge temperature(275 degs)
    4 blinks=discharge temperature below 90 degs. for 1 hour,
    5 blinks=defrost fault,
    7 blinks=outdoor sensor bad(open or shorted),
    8 blinks=liquid line sensor bad(open or shorted),
    9 blinks= bonnet sensor failure(dual fuel system),

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Alpine PKG-RSE2 Car DVD Player.


Hi,

It is difficult to get unlock code for Alpine PKG-RSE2 Car DVD Player
To get the code you can contact them.

Main support number 800-421-2284


Goodluck..

Apr 08, 2008 | Alpine PKG-RSE2 Car DVD Player

1 Answer

York was working normally. Why is it now indicating code p4?


http://errorcodeairconditioning.blogspot.com/2010/10/york-error-code.html?m=1

This is a link. If you "Find in page P4" it shows a compressor inverter failure. Assuming this is your unit. Need a model and serial #?

May 27, 2015 | Heating & Cooling

1 Answer

34 garthdale ct. north york ont. give me the postal code


There are multiple units at this location, for unit 1 the code is:
1-34 GARTHDALE CRT
NORTH YORK ON M3H 5P8

Nov 18, 2014 | Computers & Internet

1 Answer

York p3hu furnace isn't blowing air


Look at the back of the service panel to the unit. It should have the troubleshooting led codes on it.

Dec 14, 2013 | Tools & Hardware - Others

1 Answer

My York Stellar heat pump runs for some time normally. Then the thermostat light starts blinking 4 times (error code 4). However, the discharge line gets normally hot. It will work ok again for a time...


Your outside unit has a processor with an LED that also blink the error code. Check the ledger on the access panel, instruction sheet or on processor for explanation of the code

Mar 26, 2011 | Coleman Heating & Cooling

1 Answer

The light on the control board if blinking 6 times, how do I get rid of it? the light is saying VH VC. David Stowers


I think that you need to turn off power to the unit and reverse the 240v wires that are on the transformer,I think that the polarity it backwards,I had a similar problom with 2 york units,good luck!

Jul 09, 2009 | Carrier 38CKC030 Air Conditioner

1 Answer

York high effenciency furnace not firing all the time


has anyone worked on this furnace because the error would indicate that the positive 120 volt and the neg 120 volt is swapped , these units will also do this when the ground wire to the furnace or gas valve or furnace or @ the panel is lose , corroded , or missing , the gnd must be present to open valve , I am aware that ac is is not usually polarity sensitive but in this case it most certainly is ...have seen many time and know it to be true

Dec 27, 2008 | York Yankees Bedding MLB Comforter

2 Answers

York


I have an old York outside compressor/coil/fan unit, CDHF36-6A, that I need to replace as it is no longer repairable. What is the capacity of this unit and what Carrier unit would be a good replacement?

Adair

Oct 31, 2007 | Heating & Cooling

Not finding what you are looking for?
York Yankees Bedding MLB Comforter Logo

Related Topics:

422 people viewed this question

Ask a Question

Usually answered in minutes!

Top York Sport & Outdoor - Others Experts

paulcarew

Level 3 Expert

2430 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a York Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...