Question about Alpine TDA-7563 Cassette Player

1 Answer

TDA7564 When power is hooked up I get no sound out of the speakers. Everything else seems to be alright. Tape runs and ejects fine and lcd screen lights up. What's wrong???

Posted by on

1 Answer

Re: TDA7564

Internal amplifier.. I have the same problem. When you set the volume in 0 much time, trend to happen it.

Posted on Jan 02, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I installed radio everything works except no sound from aftermarket speakers. Radio was hooked up in another car everything worked fine!

Double check your speaker connections. Make sure + goes to plus and - to minus (phase) and make sure all are grounded properly. Is there an amp possibly in line? If so, make sure connections are good there also make sure powered up (it happens to all of us)

Feb 26, 2011 | Kenwood KDC-MP228 CD Player

1 Answer


Disconnect all the speaker leads and then hook one speaker (a new, known to work speaker) up directly to the radio using a short (6"-12") piece of speaker wire. Does that speaker work then?

Jan 03, 2011 | Clarion M255 AM/FM Marine CD Player

1 Answer

My pioneer deh-p840mp powers on and flips open, and seems to function fine with the exception of no sound going to all my door speakers and the bass to my subwoofers is a far sounding muffle even as I turn...

Un hook all your speakers that the deck is powering and hook them up one by one sounds like u have a shorted speaker or wire and the unit is going into protection.The best way to chk the speakers and wires is with an ohm meter . Check each speaker wire to ground and across the speaker and see iof you have any shorts. The next step woulk be to remove the unit and have it bench tested.

Jul 30, 2010 | Pioneer DEH-P840MP CD Player

1 Answer

Clarion 3475 speakers wired, player wont turn on

The RED from the clarion wire must be hooked up to a switched power source ... that was wired to your old radio, then press the reset switch, and it should then turn on.

May 05, 2009 | Clarion DRB2475

2 Answers

Chevy Tahoe radio wiring problems

I had the same problem and here's what fixed it. By default, I did not connect the blue/white striped remote wire to the harness. Apparently there is an amp somewhere in the vehicle I did not know about. After looking at the factory wiring and the aftermarket harness, I noticed that the remote wire was used and I connected it with the remote wire on the harness and everything came up and worked perfect.

Jul 11, 2008 | JVC KD-G110 CD Player

2 Answers

Stereo display works fine, but no sound to speakers.

The wires may have gotten wet and fried something in the sound output in the stereo.

Jun 16, 2008 | Pioneer DEH-1900MP CD Player

1 Answer

Infinity sound system for 2005 montero

There isn't an inbetween on sound. You either get nothing or you have something going wrong with your wiring some where. Have you tried hooking a speaker up directly to your cd player? Sounds like you have a speaker grounding out. Some times it's better to just open up your dash and unplug everything, (remove your fuse from the fuse box for your radio first). Start from scratch, if you have RCA's electrical tape them and any other metal components. That will create a grounding problem.
Hope this helps!

Apr 16, 2008 | Car Audio Receivers

2 Answers

My Cd and iPod doesn't have sound

Alright I fixed it. My stock Jeep stereo had a speaker amp that was wired in with the power ANT, the kenwood would turn the power ANT off when using other medias. So I had to hook up the BLUE power ANT wire up to the RED IGN wire so that when the car was on both the ANT and AMP would be on when the car was on. There are other ways of hooking this up I could have hooked the ANT wire up to the AMP wire coming out of the Kenwood so that the AMP and ANT would've only been on when the radio was on, but I'm happy with the way this turned out.

Dec 01, 2007 | Kenwood KDC-MP435U CD Player

1 Answer

No output when I play a CD

what kind of vehicle do you have? i am going to guess your vehicle has a stock amp that it uses to power your speakers? you will have to hook up the remote wire for the amp to the wire that powers the amp in your vehicle (the stock amp) right now it seems like you have the "power antenna" wire hooked up to the stock amp in your vehicle.

Aug 24, 2007 | Eclipse CD7000 CD Player

Not finding what you are looking for?
Car Audio Receivers Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Alpine Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4679 Answers

Jose Velazquez
Jose Velazquez

Level 2 Expert

227 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Alpine Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides