Question about Samsung LN-R328W 32 in. HD-Ready LCD Television

1 Answer

Samsung 32 inch remote control problem

Model LE31R51B 32 INCH LCD TV
i HAVE A PROBLEM WHERE THE REMOTE DOEAS NOT OPERATE ANY FUNCTION EXCEPT THE VOLUME. THE RED LED ON THE MAIN POWER SITCH FLASHES WHEN I SEND A COMMAND BUT NOTHING HAPPENS

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had a similar problem. Take the batteries out of the remote, press down on the number 5 for about two minutes the put the batteries back in. This worked for me.
(I got this tip from a telesales advisor. I was close to buying a replacement remote but this tip worked. Hope it does for you. I'm not sure on the science part of it but it basically resets the remote. Good luck)

Posted on Jun 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony Bravia KDL-40EX500. Plugged in power and no backlight. No pic no sound. Could it be the power board or inverter board? How can I test these boards? Thanks.


SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to fl ash. The number
of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the
instruction manual for the user's knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to
review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will fl ash a set number of times to indicate the possible cause of the problem. If there is more than
one error, the LED will identify the fi rst of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a "0", no error has occurred .
Diagnostic Item
Description
Number of times Standby
LED blinks Possible Location
Main Power Error 2 G2HE/GD2 (Power) Board
Audio Error 3 A (Main) Board
Balancer 4
LCD Panel
Inverter Board (ETC-Inverter MT Board) for 32" & 40" Models
TCON Error
5
LCD Panel
TCON Control MT Board
HFR Error 5 LCD Panel
Backlight Error 6
LCD Panel
Inverter Board (ETC-Inverter MT Board) for 32" & 40" Models
Temperature Error 7 A (Main) Board

This should help you narrow it down. I am also attaching the service manual for you. https://files.acrobat.com/a/preview/16a56e45-a439-48bc-8770-21638f2bab68

Jul 04, 2016 | Sony Bravia Kdl-40ex500 Series 40-inch Lcd...

1 Answer

HI, MY NAME IS S. A. ANSARI, I HAVE A SHARP AQUOS LC-32A66M LCD TV. ONE DAY SUDDENLY GOES INTO STAND BY MODE. NOW WHENEVER WE TRIED TO TURNED IT ON, IT ON FOR 30 SECOND I.E. WE CAN SEE PICTURE, HEAR SOUND...


Hi Ansari
It sounds like a main board problem. The control voltage that goes to back-light inverter board; from the main board, goes down. Contact any service technician. This is not a user repairable fault. Gopakumar Gopalan Google

Feb 27, 2014 | Sharp LC-32A66M 32 inch Multi-System Full...

2 Answers

My 32" Samsung lcd tv won't turn on, led is solid red


The Main bd is bad. It is not sending a turn on signal to the power supply.

Apr 09, 2010 | Samsung LTM1755 17 in. HD-Ready LCD...

1 Answer

Vizio 42 inch remote is dead. Except volume up /


No,ur main reomte CPU is dead,this problem happen to many remotes in many tv models.Buy a new remote in this website 1-800-Remotes Factory Original.Get the same exact remote.

Jan 13, 2010 | Vizio VW32L 32 in. LCD HDTV

1 Answer

Sky remote


TV
RED + SELECT
TV
0056

press the volume button if it works press SELECT to save if not press TV again then volume repeat this step until the volume works remember to press the SELECT button to save the code.

Cheers

Little Dish Fitter

Dec 27, 2008 | Samsung LE32R41BD 32 in. HD-Ready LCD...

1 Answer

Panasonic 32 inch LCD TV will not turn on-red light flashing


its not hard to replace the bulb and you can go to any tv shop and have them order it.youll need to give them the make and model number off the back of the tv so they know what to order

Nov 03, 2008 | Televison & Video

2 Answers

Panasonic 32 inch LCD TV will not turn on-red light flashing


sounds like a hardware failure, let me know which model # it is and i will run through service manual.

Oct 23, 2008 | Panasonic TC-32LX60 32 in. LCD Television

1 Answer

Telivision volume


sounds like a sticking tact switch. an engieer would isolate the sub-panel that contains the volume and the manual programme up/down switches and then operate the TV using the remote control and see if this eliminates the problem

Oct 19, 2008 | Toshiba 32AF42 32" TV

1 Answer

Insignia 32 inch LCD TV: Can not change Channel or Volume !


I have one in my shop with the same problem. Power is the only function that works. I repaired the power supply six monts ago. Now it looks like a bad digital processor board which is non-repairable. I can't believe what's happened to the tv business. Absolutely disgusting!

Oct 12, 2007 | Insignia IS-LCDTV32 32 in. Television

2 Answers

Remote code


Use the search function, but don't give up. It takes about 20 minutes to find the correct code.
Here are the instructions
  • Set the "Mode Switch" to the desired mode such as TV for a Television.
  • Press and hold the "Mute" button and the "Select" button until the visible LED blinks twice.
  • Enter the code "991" followed by the "device number"
    1. for Televisions
    2. for "AUX 1" devices - VCRs or DVDs
    3. for "AUX 2" devices - Audio
  • You can step through the setup codes for this mode by pressing the "Channel Up" key to go forward through the codes or pressing the "Channel Down" key to go back to the previous codes.
  • You can try out each code by pressing one or more function keys such as power, volume or digit keys.
  • When you've found the setup code that works for your device, press the "Select" key.

Sep 12, 2007 | Televison & Video

Not finding what you are looking for?
Samsung LN-R328W 32 in. HD-Ready LCD Television Logo

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71608 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1646 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...