Question about Yamaha Cr-600 Vintage Stereo Receiver With Am/fm Tuner; Wood Grain Panels 0483

Open Question

Yamaha Cr-600 Vintage Stereo Receiver manual - Yamaha Cr-600 Vintage Stereo Receiver With Am/fm Tuner; Wood Grain Panels 0483

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 73 Answers

SOURCE: I have a 70's era Yamaha Natural Sound Stereo

If there is no audible physical click from the speaker output relay, after about 10 to 20 seconds, there is an electronic fault in one or both amplifier circuits, which will require repair. If you like the sound of this unit enough to pay maybe $50 give or take, get it repaired. Otherwise, you can pick a similar unit up at a thrift shop for a few dollars.

Posted on Aug 29, 2010

  • 1 Answer

SOURCE: i have a yamaha cr-600 receiver that i haven't

Check 3 amp fuses on bottom of unit and position of Pre-Out coupler switch. Should be on.

Posted on Nov 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I need to connect my older Fisher Turntable to a pre-amp before connecting to my Yamaha RX-V850?


No, you don't need a preamp if your turntable has a moving-magnet (MM) cartridge, it should work as-is! Happy vinyling =]

See page 27 of the manual:
Yamaha RX V850 User Manual Page 27

Aug 09, 2016 | Yamaha Rx-v850 Audio Video Receiver Black...

1 Answer

Where can I get a manual or any info at all for our vintage TEAC AG-78 AM/FM STEREO RECEIVER? Age..?


http://www.ebay.com/itm/Teac-Tascam-AG-78-AG-75-Receiver-Service-Manual-Original-/222026334729?

May 16, 2015 | Teac AG-780 2 Channels Receiver

1 Answer

I get static. When I walk by the receiver it will stop sometimes.


Try re-orienting your antenna. I assume that this is when you are listening to FM. Most of the wire antennas don't get hooked up, or are just dropped on the floor. If possible, hold it up vertically. Only one end of this wire should be connected, and it should go to the 75 Ohm input. The length should be at least a meter long (3 feet).

Mar 04, 2015 | Yamaha Vintage Rx-550 Am/fm Receiver...

1 Answer

Yamaha cr-640


I look for a shop that is clean, professional, and leaves a good impression it will be taken care of, you should be able find a suitable one in Melbourne.

Apr 17, 2012 | Yamaha Cr-640 Vintage 70s Am/fm Stereo...

1 Answer

I have a receiver yamaha and can't get it connected right. i get a video from s-video or AV input, but not thru the component. also only two speakers work. i need to change settings. but manual doesn't...


When you connect through component are you using three RCA cables for the video only as component is Y,Cr,Cb which is discrete luminance and color information.
vinayak_nair_22.jpg
If you don't connect all three then you might get a black and white image, the cable is color coded RGB or red,green,blue and all three are required for video only and other than that a separate red and white to connect audio.

About the audio problem how are you connecting the audio are you using the Red and White cable , if so then you will only get Stereo or Dolby Surround audio which is Virtual Surround out of the stereo input. To get full surround sound you will have to either use discrete 5.1 channel inputs to the receiver to get actual discrete sound per channel or you could also use SPDIF to get multichannel audio through one cable. Most players support digital out now a days.

Mar 02, 2011 | Yamaha Audio Players & Recorders

3 Answers

How do I reset my yamaha receiver htr5730


http://www.retrevo.com/support/Yamaha-HTR-5730-Receivers-manual/id/1075bh230/t/2/

Page 52

1 Hold down STEREO on the Front Panel
"Factory Preset" appears on the front panel
2 Press STEREO to select the desired setting.
'Reset' To reset to factory presets
'Cancel' to cancel without making changes
3 Press STANDBY/ON to confirm your selection

Jan 15, 2011 | Yamaha HTR-5730 Receiver

1 Answer

Is there any DTS decorder player that suit with Yamaha RX-V 2090? Thank you.


Try the Technics SH-AC500D Digital Surround Processor. Its outputs should match the inputs on the RX-V2090. I own both units, though I am using a DDP-1 with the Yamaha receiver. I use two separate amps with the Technics to achieve surround sound using my good vintage stereo system (two of them actually - one for front and ane for rear). The Technics is a nice piece of kit.

Aug 13, 2008 | Yamaha RX-V2090 Receiver

Not finding what you are looking for?
Yamaha Cr-600 Vintage Stereo Receiver With Am/fm Tuner; Wood Grain Panels 0483 Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5056 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...