Question about JVC RX-6040 Receiver

2 Answers

The sound cut off for a few seconds when the reciever warm up

I have a JVC RX6040 it just started to happen i had the reciever for 2 to 3 years

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Can't we just replace the board?

Posted on Jan 09, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine did this too, just before the dsp board went. start looking.

Posted on May 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

"Dspng" what does this mean it comes on when i turn on my jvc receiver. I have no sound from my speakers used the same speakers on a different radio and they worked fine Rx6040 is no longer good


This could be a message indicating that the digital signal processor is defective or that digital signal processing has failed. In either event, it is likely that your JVC receiver is not working correctly.

Jul 17, 2016 | JVC Audio & Video Receivers

1 Answer

Pioneer vsx-522k Receiver Sound skip on SD only


use the hdmi from player to tv, use seperate coax or optical cable from player to reciever for your sound

Mar 02, 2013 | Audio & Video Receivers

1 Answer

Using the samsung HWC500 as a receiver/switch for home theater. Audio to speakers cuts out at start of each commercial for about 2 seconds. I have cable receiver plugged into samsung through HDMI,...


most likely your samsung has an active search for inputs. normally to solve this problem is to try moving input of hdmi into a different port on samsung reciever or see if maybe your manual states you can shut off this automatic audio switching. what happens is receiver will actively seek another input when sound cuts out like between commercials or movie/commercial because no sound will be coming through hdmi cable for a sec or 2. Read your samsung manual carefully it might state how to get around it but some don't so that's why i say try a different input to see if it will still do it because some hdmi inputs will be more dominant than others or have a longer delay before searching other inputs for audio.

Jan 06, 2011 | Audio & Video Receivers

1 Answer

HDMI signal cuts out for a few seconds constantly from receiver to television. It does it when switched to cable box and the roku box. Onkyo TX-SR606 Scientific Atlanta Cable box thru HDMI Roku Box...


Mine did the same thing where the screen would go black for a few seconds and then the picture and sound came back. I would try (1) switch HDMI cables, (2) try a different HDMI input in the back of the receiver, (3) try different input in the back of the TV. None of these seemed to work with mine. I finally ended up running the cable box direct to the TV and only run the audio through the reciever via coax or digital. No more problems. I think the HDMI inputs in the back of the reciever have a problem continuously carrying the signal if it is the leaset bit weak.

Sep 08, 2010 | Onkyo TX-SR606 Receiver

1 Answer

Reciever Shuts Off


chances are the speakers are the problem. try disconnecting the speakers and turn up to the level where it cuts out,if it does not cut out chances are a defective speaker or speakers,usally midrange or tweeter

Apr 10, 2010 | Pioneer SX-315

1 Answer

My reciever plays then cuts out


They don't overload from missing speakers. I'm curious, what buggered the one speaker?

Examine all of your speaker wires carefully to be sure no unintended contact is made between them and anything else.

Is "overload" being displayed?

“OVERLOAD” starts flashing on the display.

Speakers are overloaded because of high volume.

1. Press STANDBY/ON on the front panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the volume.
----------------
Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear after turning on the receiver again, unplug the AC power cord, then plug it back in again.
If speaker wiring is not short-circuited, contact your dealer.

Mar 31, 2010 | JVC RX-6042 Receiver

2 Answers

Sound Cutting Out


Somthing is tripping th amp breaker...
Try unplugging it for several minuets & see if clearing it helps..

Hope this helps !!
Please rate me good ;o)

Jul 11, 2009 | Teac AG-780 2 Channels Receiver

1 Answer

Rx6040b receiver


I need to know how to hook up all the wires to the to dvd tv cd every thing where does the wires go help me help me please i want to watch tv where it sounds good so if some some one can help me i will be very gratefull thanks

Apr 15, 2008 | JVC RX-6040 Receiver

1 Answer

JVC RX6040 OVERLOAD TROUBLE


clean your volume control if that does not help take it to a tech for repairs.

Mar 29, 2007 | JVC RX-6040 Receiver

2 Answers

Kenwood Reciever VR-615 S/n: 20102759


I HAVE SAME PROBLEM,I HIT RECEIVER ON RIGHT SIDE & DISPLAY LIGHT COMES ON.WHY I DON'T KNOW

Sep 25, 2006 | Kenwood VR615 Receiver

Not finding what you are looking for?
JVC RX-6040 Receiver Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Rod
Rod

Level 2 Expert

224 Answers

Are you a JVC Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...