Question about Air Conditioners

1 Answer

I have a sunbeam electric blanket that is probably about 10 years old. My parents are visiting and it is showing FF and it is not heating any ideas as to what I need to do to fix it or should I get rid of it and get another one?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

Unforturnately the best idea is to buy a new one. It is dangerous to try a repair.

Ray

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I plugged in the cord to the blanket, it displays a continuous blinking of the letter F


Sunbeams - blinking "F" means that the connection to the blanket was loose. Make sure you give it a good push to get the piece fully engaged.

Nov 18, 2014 | Sunbeam Twin Electric Auto Heated Blanket-...

2 Answers

Can electrical cord for electrical blankets go between mattress and box spring


Wires should be on the floor. Do not put them where you may lay on them and or cause friction on them (even if it's just rolling over during the night).

Sep 19, 2014 | Sunbeam Twin Electric Auto Heated Blanket-...

2 Answers

Power cord for the Sunbeam electric twin blanket


Haven't you contacted the company that shipped it to you? It might have been an oversight and they'll mail you one. You can do that for anything you get shipped to you from a company.

Nov 28, 2013 | Sunbeam Twin Electric Auto Heated Blanket-...

3 Answers

Sunbeam electric blanket flashing ff when I try to turn it on.


Ok folks. I fixed it. I unplugged and then waited and replugged and started at high or 9 and then it went to FF in 60minutes or a couple of minutes. I scratched my head and tried this fix--instead of starting again at 9 or H I started at level 7. That did it. FF most probably indicates excess current, and the H or 9 probably is too high to set. So unplug -repluf-turn on and dial 7 or lower. It should fix it. Or buy a new one.

Dec 11, 2008 | Air Conditioners

3 Answers

Electric blanket controller light blinking


i had the same problem , i believe it was caused by unplugging the blanket plug while it was in the on position , i unplugged it from the wall and it like reset itself , worked for me.

Sep 20, 2008 | Air Conditioners

12 Answers

My Sunbeam electric blanket controls blink when I plug the control cable into the blanket. I cannot turn the controls on or off.


Same problem, but now it is ok.  I emailed Sunbeam and was told that if my blanket was not plugged directly into a wall outlet it was not getting enough power and I needed to plug it into a wall outlet taking these steps:
1) Unplug from the surge protector/extension cord 2) Unplug from the blanket 3) Plug back into the blanket 4) Plug into a wall outlet

Jul 21, 2008 | Air Conditioners

Not finding what you are looking for?
Air Conditioners Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Conditioners Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Bill Long

Level 3 Expert

577 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you an Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...