Question about InFocus ScreenPlay 4805 Multimedia Projector

1 Answer

Slanted Border- Projector image is not square

My Pj projects a picture that is tappered on one side. In other words the left edge of my screen is 36" and the right side is 33". This creates a slanted border at the top of the projected image. None of the keystone options have an effect on this problem. Is there some other reason I would be experiencing this issure?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 167 Answers

Is the image slanted on the bottom as well?
Make sure the projector's throw is pointed directly at the target ie. screen or wall etc. there's not much else it could be.

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust view from an angle?


Best to have the projector 90 degrees up and down and left to right to the screen. Try turning the projector to move the image left or right.

Aug 30, 2014 | Multimedia Projectors

1 Answer

Words are spelt backwards


Your projector has been set up for rear projection mode (projecting the image from behind a translucent screen. You need to access the setup menus and reorientate it for front projection. Using a mirror to view the image whilst navigating through the menus may help :o)

Mar 27, 2014 | NEC VT465 Multimedia Projector

1 Answer

How to change setting picture just opposite


If opposite means that you want to rotate the image or picture for projector mount in the ceiling.

KEYS location: (keys are located back side of the projector there is 2 keys 1 for menu and second is a joystick witch have 4 arrow keys and center press is a enter key)

Press MENU button to display the menu screen.
then use joystick UP and DOWN to select the OPTION menu. Press joystick for ENTER to display the option screen. Then press joystick UP and DOWN to select INSTALLATION.
Then press joystick RIGHT and LEFT to select your required image rotation there is four type of rotations.
1. FRONT DESK
2.FRONT CEILING
3.REAR DESK (A translucent screen is required for rear projection)
4.REAR CEILING (A translucent screen is required for rear projection)

If opposite means negative to positive so there is no any setting in your projector witch is chang your picture or image positive to negative.

Jan 21, 2011 | Panasonic PT-LB60NTE LCD Projector

1 Answer

The top of the screen is slanted while the sides of screen and bottom are even, causing the right hand side of screen to appear smaller than the left. Anyway to fix this?


Sounds like a "keystone" problem. Your projector needs to be oriented to the screen in an exact manner. Manufacturers provide "keystone" correct to adjust for mis-alignment. If proper orientation is impossible, use the keystone correction of the unit to adjust your edges.

Aug 14, 2010 | Hitachi Cine Master PJ-TX200 Multimedia...

1 Answer

Picture is not square on screen right side considerably higer than left _ can't get it squared


Have you tried the keystone correction. You must have the projector squared/lineup to the area you are projecting.

Jun 17, 2010 | InFocus Multimedia Projectors

3 Answers

Projector image is too large for screen


Hello,
There are no other lenses for the LP600 :(

Cheers

Jan 27, 2009 | InFocus LP 600 Multimedia Projector

1 Answer

Infocus image problem


That is caused by a collapsing light pipe.
This is a mirrored glass square component that is located directly behind the color wheel. It is comprised of 4 mirrored section approximately 40mm x 8mm that are glued together with a hi-temp adhesive to form a square. The artifact you see is one of these mirrored glass section's has come unglued and has moved inwards blocking one edge of the image. The edge of this shadow is not shar because this failure is not at a focal point.WHEW..all that being said it's possible to re-glue it if you are electro-mechanically savvy and have steady hands. If you need to take it to a service they will most likely just just replace the complete DLP engine (the whole optic assembly) Hold on to your wallet!!


Cheers

Nov 06, 2008 | InFocus LP120 / 1000 Lumens / XGA / DLP...

1 Answer

Hitachi PJ-TX10 alligment


i have one of these projectors found on setting it up that the projector must be square on with the screen, the pjtx10 doesn't have ant "wedge type" setting like sony does. if this doesn't fix problem there is some thing not aligned in the lense

Mar 04, 2008 | Hitachi PJ-TX10 Multimedia Projector

1 Answer

Sanyo plv z4


look in the projector menu ( should not be backwards) and switch the view to front projection. It might be set in rear projection. That is what my viewsonic PJ-558 projector can do sometimes

Jan 26, 2008 | Sanyo PLV-Z4 Multimedia Projectors

Not finding what you are looking for?
InFocus ScreenPlay 4805 Multimedia Projector Logo

1,076 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Multimedia Projectors Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you an InFocus Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...