Question about RCA Universal Remote Control

1 Answer

I have a Manavox TV/DVD/VCR combo. The remote stopped working. Can you tell me why and how to fix it. Mean while I purchased a RCA universal remote and it did not come with a code for my combo unit. Can you tell me if the RCA remote has a code for the Magnavox combo? Thanks

Posted by on

  • mdpraet Jan 30, 2009

    I have a Magnavox TV/VCR/DVD combo original remote no longer works. I purchased a Radio Shack universal 5-in-one remote. Tried the codes listed and nothing works. Help

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

First of all, make sure you have good batteries in the original remote(I have seen brand new batteries be bad) and make sure that the connections are clean. Then make sure that the remote is in TV mode and see if it will work your TV. If there are no codes for your TV that came with the RCA remote, you will need one that does, or you will need to replace the original remote. I have seen a lot of times where universal remotes will not work combo units at all, no matter if there are codes listed or not.

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have two RCA remotes. 1st RCU 310 5538P. 2nd RCU 400 2420BB.


Remote Control Support - RCA ' Made for Moments

www.rca.com/support-remotes

RCARemote Control Support. Select your Type of Remote. Remote Code Finder ...RemoteProgramming. Cable/Satellite Receiver Codes. Select Your Provider.

RCA Universal Remote Control- Target Programming ...

www.thompsontv.com/rcarc.html
RCA Universal Remote Control-Programming Codes. ... Universal Remote. The remotemay already be set up to operate your brand of TV, VCR, or Cable Box.

Program an RCA Universal Remote Without a "Code Search ...

www.wikihow.com > ... > TV and Home Audio > Television

wikiHowHow to Program an RCA Universal Remote Without a "Code Search" Button. Do you have an older RCA universal remote that you want to use, but it lacks a ...

Jan 23, 2016 | RCA Remote Controls

2 Answers

I need code for philip s remote for a sayno ty


Philips rca universal remote codes sayno vcr dvd combo ...

www.fixya.com > ... > Remote Controls
Universal Philips Magnavox remote for a Sanyodvd vcr combo ? I have a cableremote and need to program my Magnavox vcr/dvd combo into it i have 2 dvds ...

How to Reprogram a Philips Universal Remote Controller ...

science.opposingviews.com > Computers

Dec 21, 2015 | Philips Remote Controls

1 Answer

It's not working what can I do to program one for all controller to rca tv


HI,
The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box. To control devices other than the default brands, perform the following steps; otherwise skip this section:

HOW TO PROGRAM

1.Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc)

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step.

( CHECK THE BELLOW ADDED LINK TO FIND THE CODE )


2.On the remote control, press a device key once (i.e., DVD/VCR, CBL/SAT, or TV).

NOTE: To program control of a VCR, PVR (or DVR), TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCRonce. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions.
NOTE: To program control of a DVD Player, DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD/VCRonce. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SATonce.

3. Press and hold SET until the LED (red light) blinks twice, then release SET

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LEDdid not blink twice, repeat steps 2 through 4 and enter the same code again.

5.Aim the remote control at the device and press POWER once. The device should turn off.
If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For next code.

NOTE: If the device does not have a POWER key, press PLAY

6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code following.

Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...
Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...

Jan 25, 2015 | RCA Remote Controls

1 Answer

Need code for bd20tf10


Go here for all information regarding the RCA BD20TF10 remote. You will need to download the original manual for the RCA BD20TF10 TV/DVD/VCR combo, and in the manual, it will tell you all codes and how to program the remote. Note: this remote does not program to any other TVs, only work RCA TVs.

Oct 06, 2012 | RCA Universal Remote Control

1 Answer

I have an RCA universal remote control CGEU401 and have successfully programmed the sony TV. However I have been unable to do so for the Nexxtech VCR/DVD combo model 1619001. I have tried code searc


If there is no setup code in the code list of the remote to serup your Nextec VCR/DVD with RCA universal remote, the remote cant be set to that device. That is all.

Apr 15, 2012 | Remote Controls

1 Answer

I was wondering some codes for a RCA tv/ vcr combo


have a old rca television with a build in vcr. connectec a cable box remote works only for volume and channel but power button does not work, with remote was set and stop working call cable company and was told to contact rca to recieve codes for television

Sep 30, 2009 | Philips Universal PH301S Remote Control

2 Answers

Cannot find remote code for panasonic TV/VCR combo for RCA remote


Here is a list of codes for your remote. Please follow any of the links below to get your codes.
Results 1 - 10 of about 324,000 for rca universal remote codes. (0.26 seconds)
Search Results
  1. RCA Universal Remote Control-Programming Codes RCA Universal Remote Control-Programming Codes. ... The remote may already be set up to operate your brand of TV, VCR, or Cable Box. ...
    www.thompsontv.com/rcarc.html - 33k - Cached - Similar pages -
  2. How to Program an RCA Universal Remote Without a "Code Search ... wikiHow article about How to Program an RCA Universal Remote Without a.
    www.wikihow.com/Program-an-RCA-Universal-Remote-Without-a-%22Code-Search%22-Button - 42k - Cached - Similar pages -
  3. Universal Remote Control Codes Codes and links for a number of universal remote controls, including Sony, RCA, Memorex, Radio Shack, One For All and more.
    www.xdiv.com/remotes/ - 73k - Cached - Similar pages -

May 05, 2009 | RCA Universal Remote 3 Device Remote...

1 Answer

Need code for Emerson TV,DVD,VCR Combo


you can set up any like this
1. turn on what ever you want set up
2. press and hold set up tell light blinks or stays lit
3. push what you are trying to set up t.v. or dvd ect.
4. push power on/off tell it turns off
5. push enter when it turns off
Thank you for useing fixya please rate me

Feb 12, 2009 | RCA Universal Remote 3 Device Remote...

4 Answers

Need code for Emerson TV,DVD,VCR Combo


I don't know if you guys even need this advice anymore, as it's 1-2 years late, but if your universal remote has a VCR setting, the Emerson 13" CRT TV/VCR combo I have operates under that mode.
The code I used was 002. These may also work: 278, 184, 479, 000, 121, 211, 037, 043, 061, 208
Remember, program your remote as if you were setting up a VCR (and NOT a TV). For instance, on my GE universal, I hold the "code search" button down until I get a steady light. I hit VCR, and then I entered 002. Works like a charm.

Mar 25, 2008 | RCA Universal Remote 3 Device Remote...

Not finding what you are looking for?
Remote Controls Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68157 Answers

andy williard
andy williard

Level 2 Expert

226 Answers

Cindy Wells

Level 3 Expert

4753 Answers

Are you a RCA Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...