Question about E-Machines Emachine T5026 power supply ** FREE SHIPPNG ** (EM12EB324PIN) Power Supply

2 Answers

Wont boot Have a emachine D2046,motherboard D33007. wont boot but gives a long beep.

Posted by on

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have a emacine e725 an is asking for a bott disk need copy or download

Posted on Mar 06, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If it is checking the key board and hard disk lights are ON ,then try fixing the memory card(s) frist after taking out one by one. If it still dont work check your hard disk by testing it on some other PC.If it dont work ther also than Disk is crashed.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

System unit or power supply?


The computer power supply may have failed. Do you get the "post beep"?

If not- remove the BIOS battery, move the jumper to "Clear BIOS" . Insert BIOS battery, and try to boot. Put jumper back to normal position and try boot again. If you do not get the post beep, swap power supply for a known good one, and try boot again. If it still does not boot and give you a post beep, look to see if there is a removable BIOS chip- pop it out and put it back in.place, this will clean the terminals. Go through and reset BIOS, as above, and try boot. If the system is functional, it should now boot up, but prompt for you to run the setup program.

If it does not boot, the problem is relating to motherboard/processor.

Apr 11, 2012 | System Power Supplies

2 Answers

AMD sempron power supply


Hi,

I would venture that "shows winfast on monitor" indicates the type of Video Card that your PC is using. Thereafter it should go to POST showing the motherboard, BIOS, memory count and others.

Since as you posted, after Winfast nothing follows, I can only suspect that you have a motherboard problem or at least a BIOS corruption.

Please post back the brand and model of your computer or at least what motherboard.

Good luck and kind regards.

Thank you for using FixYa.

Mar 16, 2008 | System Power Supplies

1 Answer

I have a T5026 EMachine won't power up. Green light on motherboard is on , could it be the switch , tried putting a new power supply box in it.


to see if the power swithc is the problem-

first, try to isolate the wire that connects the power switch to the motherboard. once you have deternined where the power switch plugs, then remove the wires from the motherboard leads and try to short the leads by connecting them with a metal device like a screwdriver tip. if the switch is broken, it will boot when shorted with the screwdriver. if it still will not boot, then you probably need either a new motherboard or a new cpu.

Nov 06, 2010 | E-Machines Emachine T5026 power supply **...

1 Answer

EMachines T3828 won't turn on. Any way to determine whether problem is power supply? thx!


Had the same problem and ended up replacing the PSU. Try re-seating the memory and video card first but if your not getting any power on beep codes then it is likely that the PSU and possibly the motherboard have failed (google emachines power supply failure).
Try a new PSU, it worked for me and was a fairly cheap fix if nothing else works.

Sep 19, 2009 | E-Machines Emachine T5026 power supply **...

1 Answer

Computer does not start it just makes beeps


You have a component that has failed. You have two options. Option 1 is locate the beep codes either online or in your manual and fix what those beeps tell you is the problem. Option two is reseat every component you can - memory, cables, any cards in the motherboard. Blow the dust out of the case with some canned air.

Thank you for using the FREE section of FixYa.

Jun 29, 2009 | E-Machines Emachines MXM-145TF1 Power...

1 Answer

E machine wont boot just beeps constantly screen


motherboard most likely blown,contact me on my support pages on http://www.motherboardsrus.net

Jun 07, 2009 | E-Machines Emachine T5026 power supply **...

2 Answers

EMachine T5026 no boot


This just happened to my t5026. I had to replace the power supply to fix.

Mar 08, 2009 | E-Machines Emachine T5026 power supply **...

2 Answers

Computer is an eMachine


Well Most Likely Your Problem Is A Bad Connection Of Power To The Hard Drive Or Motherboard Also You Should Check The IDE Or SATA Cable That Goes From The MotherBoard To The Hard Drive Is Securely Connected On Both Ends

Nov 24, 2007 | Instek Power Supply, Triple Output, DC,...

Not finding what you are looking for?
E-Machines Emachine T5026 power supply ** FREE SHIPPNG ** (EM12EB324PIN) Power Supply Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines System Power Supplies Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an E-Machines System Power Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...