Question about Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Dryer runs no water enters condenser draw, empty water light on.

Hdryer runs no water enters condenser draw, empty water light on.I have cleaned all filters and condenser pipe to condeser draw clear .HOTPOINT AQUARIOUS CDT40 CONDENSER DRYER.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 3,463 Answers

Remove the filter draw on the bottom left, and wash out under running water to flush out all fluff.
Reach inside opening and clean as much fluff anf gunge as you can from the cavity.
Get a plastic bag tie, reach and feel for a small at the rear of the compartment, and poke hole clear..
If this does not solve the prob, then it is probably a sticking or faulty float valve., or switch.
This involves a complete strip down to access these components.
Plz rate my solution.
Thanks.

Posted on Jan 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is water in the dryer vent line


There can be multiple reasons for this. If the vent line exhausts to the outside, it is possible that if the vent louvers are stuck open and rain may enter the line when windblown. More common is that dryer vent air is hot and moist due to the water being evaporated from the clothes. If the vent line runs through a cool/cold area, condensation may form in the vent line. If there are sags in the line, condensed water can accumulate in these places.

Sep 06, 2014 | Maytag MDE9700AYW Neptune 174 Electric...

1 Answer

Condenser dryer


PULL OUT THE PLUG
on the bottom right on the back is the water pump
it needs cleaning or replacing
not lifting the water to the water draw

Dec 12, 2013 | Creda IWD12 Front Load Washer / Dryer

1 Answer

WONT DRY


Hi there, if your dryer is a condensing dryer then perhaps you need to empty the collector bottle , its is a compartment on the side of machine , open this and remove the bottle , this must be done after at least two sessions of drying. On the other hand if your dryer is of the vented type with a 4 inch flex vent it must be vented through the wall to the outside with no kinks in it , the reason for this is the water turns to vapour , and must exit the machine or you will have clothes that are still wet and water will collect at the bottom, its the same principal for the condenser machine only you have to empty the bottle of condensed water or the same result will occur.
Hope this is of some help to , Cassyjoe.

Nov 07, 2012 | Washing Machines

1 Answer

Clothes not being dried in drying cycle. Fan is working.


Your washer dryer will only dry half the clothes that it can wash, so you may need to reduce the amount your trying to dry. Also the drying side works by condense drying,it wont be vented outside, it needs a trickle of water which runs behind the draw where you put the powder in. When its on pull out the draw and check that there is a trickle of water going in, if not it's the solenoid valve gone, not a major job to change, and it is a fairly common fault. Have you checked the hose that leads to outside? They get stuffed with lint,etc and sometimes they need to come off the dryer and the blockage removed, or buying a new hose could be necessary. Check the exit point on the machine and the entrance and exit point in the wall of the building. Make sure your lint trap is the machine in clean and it should be washed every three months.

May 17, 2011 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

I have a new (1 month old) Hotpoint Condenser Dryer (TCD980G). When it is on the drying cycle it runs for about 30 minutes and then trips the RCD circuit. I have cleaned the condenser filter and the water...


There should be no condensation present if it is a condenser dryer, this is the idea of it.
As for tripping the electrice, then it suggests to me that the steam could be the cause of the problem.
As it is a new dryer, then I would strongly advise you ring Hotpoint service, or ring the help line number in your instruction book.
You can contact them at the following address if needed.

WWW.HOTPOINTSERVICE.CO.UK

Jan 01, 2011 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Wd440 not drying. how does the fluff get emptied?


Because it is a washer dryer, there is no fluff filter to clean.
It is self cleaning, because the fluff is washed away by cold water entering the condenser and flushing the fluff away.
Trust this answers your query.
Please rate my solution.
Thankyou.

Jan 25, 2010 | Hotpoint Washing Machines

2 Answers

Dispenser draw filling with water, i have been told there is no filter i can clean!!? The part of the draw where you put your fabric conditioner in.


You have been ill advised, there is a filter that you can clean.
Remove rear panel of washer.
Remove large black hose fastened to bottom of drum.
Remove and clean filter inside hose.
Remove top cover., check the hose from dispenser to drum is not blocked with powder..
If the dispenser drawer still fills up, then it is possible that the condenser is blocked with fluff.
This a major job to put right, you would be well advised to call an engineer if this is the case.
Hope this helps.


Dec 13, 2009 | Hotpoint Aquarius WD63 Front Load...

2 Answers

Water coming out of the draw during cycle


water comes out of draw when the water is emptying and on a spin. have tried it on the drain button to see if it did the same and there seems to be no problem on this function, only seems to be a problem when spinning, not sure if something is blocked.

Feb 15, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

2 Answers

Drying cycle - laundry comes out wet!


possibly that drain pump is not pumping out - washer dryers take in water during the dry cycle. check filter

Mar 17, 2007 | Bosch Classixx WVF 240S Front Load Washer...

Not finding what you are looking for?
Hotpoint Aquarius WMA42 Front Load Washer Logo

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...