Question about DameWare NT Utilities

1 Answer

Can't connect to Desktop PC with Dameware using Netgear Router

I went from a Netgear Router, to the same model of Netgear Router because the original one got stepped on. Well, now, with the new router, I can't use dameware to connect to my desktop pc.

Can someone help me?

AIM: BAMotumbo

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Hi brianaugusti,

You need to open a port in the new router to allow remote connection. The port used by dameware is 6129, and the windows remote port is 3389

Please provide the model of your router so I can assist you with the next steps and how to open the ports.


Posted on Mar 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have installed a antamedia dhcp server, but it does not give out ip addresses. please guide me on how to set this up. i have awindows machine connected to a linksys router 10.0.0.1 and the computer int...


Make sure DHCP is off on the Linksys router first, set the IP of the router inside the scope of your DHCP server's scope (set it as the gateway so if your using 192.168.1.X, set it to 192.168.1.1). After that, remove static IP settings on your desktop (except the one using DCHP, set that to 192.168.1.10)

Mar 01, 2011 | Antamedia DHCP Server

2 Answers

I don't remember my WEP key for my wireless


Reset your router .Just about every modern router can be reset by following a very simple procedure. Either flip it upside down or look at the back for a small hole with the word RESET. All you have to do now is just find a small paper clip and stick one end into the whole while the router is turned on.
Normally, you have to hold down the button for 5 to 10 seconds. At this point, you should see the wireless router flash, blink, or simply restart. Once it has fully rebooted, the router is back to it's original state.

Jan 17, 2011 | Alpine Snow Wireless WEP Key Password Spy

1 Answer

Remote desktop problem


www.teamviewer.com you can use that program to do it.


Thanks and good luck.
Ekse

May 05, 2009 | DameWare Mini Remote Control for PC

1 Answer

I have a netgear router and have a laptop hooked up to it and working but I when I have my desktop hooked up to it, the computer won't let me go online. I have an HP Compaq Presario and I also noticed that...


The most likely culprit is the cable you are using to connect the desktop to the router.

The networking icon with the red X is your computer telling you the network card is not physically connected to a functioning port. Either the cable is bad or one of the ports (your computer's or the router's) has a physical or electrical problem. Try using the laptop cable and/or connecting to the port the laptop is connected to.

If the problem is something else, it is likely more information will be needed to diagnose and fix it (router model, OS version, whether a DHCP server is running, the network address of the router, the exact type and text of the icon that's telling you the network is disconnected).

Jan 06, 2009 | Network Software & Management Tools

1 Answer

Control 4 system


I think you double posted, so I will just mimic my other answer


If i understand you right, you are playing your CD from your computer. If this is correct, you should burn your cd's into MP3 format with windows media center. Then let you Control 4 system get your music through your network.(you will need to call your Control4 dealer to setup this.) You should use a network hard drive to save you music to. but it can be done with only your computer. If you use your computer you need to make sure that your computer stays on, so turn off the screen saver and your power standby and hibernate options.


I hope this helps. If you live in Utah, I work for a control 4 dealer in Draper. If you have any more questions, e-mail me at joe.4home@gmail.com you could also visit a end user control4 site at http://www.c4forums.com/


Joe

Dec 14, 2008 | DameWare Mini Remote Control 4.x (dmrcupg)...

1 Answer

I have a Control 4 system. While playing CD's, the TV screen flashes "no signal" and the music will eventually stop. I was told to press the "fn" and "f4" key on the computer to switch itover, but it isn't...


If i understand you right, you are playing your CD from your computer. If this is correct, you should burn your cd's into MP3 format with windows media center. Then let you Control 4 system get your music through your network.(you will need to call your Control4 dealer to setup this.) You should use a network hard drive to save you music to. but it can be done with only your computer. If you use your computer you need to make sure that your computer stays on, so turn off the screen saver and your power standby and hibernate options.


I hope this helps. If you live in Utah, I work for a control 4 dealer in Draper. If you have any more questions, e-mail me at joe.4home@gmail.com you could also visit a end user control4 site at http://www.c4forums.com/


Joe

Dec 14, 2008 | DameWare Mini Remote Control 4.x (dmrcupg)...

1 Answer

How to enable router security system


Wireless security is difficult to handle simply because the manufacturers have different interfaces to the management software. Netgear has a very good description of how to set up the wireless security in the manual, if you have misplaced the manual it can be downloaded at: ftp://downloads.netgear.com/files/DG834Gv4_RMsrc_13Sep07.pdf

Any posted answer would be multipages long and simply a rehash of the manual.
I recommend using the WPA-PSK.

If you have specific questions they can be answered quickly.

Sep 23, 2008 | Network Software & Management Tools

1 Answer

Dameware asking for password?


You have to disable simplified sharing:

1. Click Start, and then click My Computer. 2. On the Tools menu, click Folder Options, and then click the View tab. 3. In the Advanced Settings section, clear the Use simple file sharing (Recommended) check box. 4. Click OK.

http://support.microsoft.com/kb/307874/en-us

Apr 11, 2008 | DameWare Mini Remote Control for PC

1 Answer

LIVE connection


Use the ethernet connection. Make sure that you reboot the router if you're using one and that there's a link light on the router on the port where the xbox is. If you have a computer, use it to make sure your connection's dns is properly configured. use the computer to connect to www.fixya.com to make sure.

Feb 25, 2008 | Microsoft Office Live Communications...

Not finding what you are looking for?
DameWare NT Utilities Logo

Related Topics:

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top DameWare Network Software & Management Tools Experts

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

caffeene

Level 1 Expert

4 Answers

Shahzad  Waseem...
Shahzad Waseem...

Level 3 Expert

746 Answers

Are you a DameWare Network Software and Management Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...