Question about Philips DVDR630VR DVD Recorder/VCR

1 Answer

Get message "Please Wait" nothing can be used

I have a Philipos DVDR630. I was recently going to watch a tape but it will not load. Instead I get a message "Please Wait". I tryed to eject the DVD but nothing happens. The please wait message stays until I turn it off. I believe that possibly there is a problem with the DVD but as I cannot eject it, it is stuck on this Please wait stuff.

Posted by on

  • sissib Jan 11, 2009

    Does anyone know if it can be fixed? As I can't get the DVD out.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 61 Answers

If the cd or dvd was scratched very much this may happen

Posted on Jan 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A SAMSUNG DVD HR753 WHICH HAS 160 HARD DRIVE


Make sure you are using the right disk IE, DVD-R or DVD+R. Most Newer DVD player's will play DVD-R but very few play DVD+R

Jun 23, 2009 | Toshiba SD-6200 Multi-disc DVD Player

1 Answer

Tape Stuck


I've checked the entire user manual which notes problems like this need to be referred to authorized service personnel. Myself, I would unplug the entire unit, put it on a kitchen table using a phillips (cross-tip) screwdriver to remove the top metal shell. Remove at least 2 screws each side and 2-5 rear screws securing the top. Nothing like peering inside to see what is causing the VCR to get stuck and help remove it. No release pinhole or tape freeing ejector will work if the unit's tape is tightly wound around some internal object or the tape is stuck because something foreign is inside the unit. Best of success. ZT3000 "Beta tester of "0"s and "1's"

Aug 17, 2007 | Panasonic DMR-EZ47V DVD Recorder/VCR

1 Answer

DVD Recorder frozen - please wait on display


You need to replace the STR-G6353 voltage regulator on the power supply board. Full proceedure with photos at this link: http://www.rbjtech.net/electrical/e85/e85.htm#0 I did this on my DMR-E85H and it now works like new.

May 30, 2009 | Panasonic DMR-E85H DVD Recorder

1 Answer

Static but no pic , only audio


The tape you were watching was probably worn and left a little of its oxide surface on the VCR's heads. This is pretty common, especially if you ever play rented tapes or tapes that have been around for a while. Plays great, then the next time, no picture.

A head cleaning cassette may solve the problem for you. Make sure you get a wet-type cleaner. Radio Shack has one on their website, and you can probably find one locally. If the VCR hasn't recently (or ever) had a good professional cleaning, it might be time for one. The whole tape path (everything the tape touches, and not just the heads) need to be cleaned and a cleaner tape can't do that. Video rental shops used to offer cleanings. Maybe one in your area still does or there's a shop you can take it to. We charged $20 some years back when I worked at a shop. Today it might be cheaper to replace the VCR than to clean it.

Apr 22, 2009 | Toshiba SD-V295

2 Answers

Voice track not matching video track


I believe Samsung have update firmware to correct that problem, contact Samsung in your area or country
Cheers

Dec 09, 2008 | Samsung DVD-VR375 DVD Recorder/VCR

1 Answer

MAGNAVOX DVD/VCR RECORDER


I have been using my machine with no problems, until recently. The machine will not stay on more than a few minutes when I try to use it, either watch a tape or tape a show. It starts, then just shuts down. When the machine is turned back on it ejects the tape????
Can you help, please.

Thanks
Sharon

Jul 07, 2008 | Philips Magnavox MWR20V6 DVD Recorder/VCR

1 Answer

VCR


you have probably bent the tab that holds the tape end sensor or its light. The tapes have a clear section at the end of the tape and the light shines through to the sensor to tell the unit that the tape is finished. The light should not pass through the recordable part of the tapes. If anything is bent the light may shine on the sensor and tell the unit you're at the end of the tape and to shut off. Some units have a tape tension sensor also that tells the unit that the tape is broken and to shut off. Only way to know is to remove power and take it apart and look for anything that may be bent. Stay away from the rotating head assembly and the posts that the tap travels on. Do not apply power with the unit open. Do not load a tape and remove power as some units freeze in the loaded position and will not load new tapes unless manually placed back in the unloaded position.

Oct 17, 2007 | Emerson EWR20V4 DVD Recorder/VCR

1 Answer

Please wait


try to clean loading sensors

Jun 03, 2007 | LG RH-4820 DVD Recorder

4 Answers

System Error


FYI...the best suggestion I've seen is to hold the channel up and play buttons simutaneously....thereby causing the machine to return to the "factory initialized" state. So far so good for me. We'll see. photog1

Apr 22, 2007 | Toshiba D-VR4 DVD Recorder/VCR

Not finding what you are looking for?
Philips DVDR630VR DVD Recorder/VCR Logo

Related Topics:

590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips DVD & Blu-Ray Players Experts

Steven

Level 1 Expert

6 Answers

Cindy Wells

Level 3 Expert

4757 Answers

rugby prop

Level 3 Expert

446 Answers

Are you a Philips DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...