Question about Routers

2 Answers

Enable password - Routers

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My pSSWORD IS IN THE DISABLE MODE I WANT TO ACTIVATE MY PASSWORD FOR SECURITY

Posted on May 12, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 55 Answers

It depends on the brandname

-tg

Posted on Jan 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset my password?


In the below example i'm setting password as cisco for enable mode & Virtual terminals of router
1)Connect to the router and follow the below steps
Router>
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret cisco
Router(config)#line vty 0 4
Router(config-line)#password cisco
Router(config-line)#login
Router(config-line)#exit
Router#exit
Router con0 is now available
Press RETURN to get started.


Test:
Router>enable
Password: (type cisco to enter into the router privilaged mode)
Router#

Aug 09, 2015 | Routers

1 Answer

Getting a new router password for linksys e1200 se up disk


For that connect your router to computer with ethernet lan cable then you can access it with below ip address in internet browser.http://192.168.1.1 or http://192.168.2.1 Type as user as "admin" and password as "admin" or blank or "password" or "1234" then you can see configuration page of router.Click on wireless settings enable it if you want to set password security then enable WEP and enter password then you can connect it.Enable DHCP and Set WAN settings and internet service provider then save settings and restart router .Let me know if you need further assistance.Thanks for using FixYa.

Oct 19, 2011 | Cisco Linksys E1000 WirelessN Broadband...

1 Answer

How do i enable upnp


Using your Internet browser, you can access the Router's Web-Based Advanced User Interface. In your browser, type "192.168.2.1" (do not type in anything else such as "http://" or "www"). Then press the "Enter" key.
Click login, the router comes with no password set, so unless you have changed the password, just click login.
To take advantage of the UPnP features, you can enable the UPnP feature. Simply select "Enable" in the "UPnP Enabling" section of the "Utilities" page. Click "Apply Changes" to save the change.

Oct 18, 2010 | Belkin Wireless G Plus MIMO (F5D9230-4)...

1 Answer

I cant enable the password


Hi Friend,

In order to enable wireless security password, please follow the steps:

1.Type 192.168.1.1 in the address bar of the web browser and hit enter
2.Enter the username and password. If you have not set the router password then leave the username blank and type admin in password and hit enter.
3.Click the tab Wirelss in the setup page and fill the sections
Wireless Network Mode:Mixed
Wireless Network Name:As per your choice
Wireless Channel-6-2.437GHz
Wireless SSID-Enabled and click Save Settings

4.Click Wireless Security and fill the sections as mentoned
Security Mode-WPA Personal
PA Algorith- TKIP
WPA Shared Key-Enter 10 digit password(e.g-your 10 digit telephone number) and click Save Settings

You have now set a password to your wireless network and is secured. Enjoy

Regards
Chiranjeet

Sep 16, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

Set up a non wep password


Hi Friend,

Please follow the steps;

1.Open the router page(192.168.1.1)
2.Enter the username and password(default password is admin and leave the username blank)
3.Click Wireless and then fill the sections as mentioned:
Wireless-Enabled
Wireless Netowrk Name-As per your choice
Wireless Channel-6-2.442GHz
Wireless SSID broadcast-Enabled and click Save settings

4.Click Wireless Security and fill the sections
Wireless Security-Enabled
Security Mode-WPA pres-shared key (as you want non wep password)
WPA Algorithm-TKIP
WPA Shared key-Minimum 8 and maximum 64 digit password
Group Key Renewal-3600 and click save settings

Turn off the router for 30 seconds and turn it on after that. Now you have a non wep secured network

I hope this will resolve the issue.

Regards
Chiranjeet

May 20, 2010 | Linksys BEFW11S4 Wireless-B Broadband...

1 Answer

I use Thomson ST585 v6 which automatically connects my desktop, but do not know password to allow visitors to connect their laptops, can I retrieve this, or can they connect if I press the black button on...


The black button on the front panel of 585's is to enable / disable the wireless network (WiFi). If the WiFi is enabled with a password setting the led on the front panel is green, if the WiFi is enabled without a password setting (free to all) the led is red. If your desktop is connected with a cable at 585, you can just use the button in order to enable (or disable) the WiFi for the visitors. If you want something more secure you can set the WiFi with a password but in this case you must tell your visitors the password in order to acess the WiFi. It's up on you to decide the way you want to use the WiFi. Of course if you need help to set up the WiFi password post me a reply.

In case of a problem or clarification, don't hesitate to post me a reply also.
If you are satisfied, rate my solution with the "thumbs".

Thanks and regards
Please kindly rate this solution
Stelios
direct FixYa link: http://www.fixya.com/users/technical114

May 10, 2010 | Routers

2 Answers

How to change password for Trendnet TEW 432BRD wireless router


First RESET your router to defaults.
for that press RESET button for 10 seconds RESET button is in back side of router.
Then connect your router to computer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.
Set WAN settings as your internet service provider settings.
Enable DHCP .
CLick on wireless and enable wi fi.
If you want secure router then enable WEP security then add new code it is your password key for connect wi fi.
Let me know if you need further assistance.
Thanks.

Nov 06, 2009 | Trendware TRENDnet TEW-435BRM 802.11g...

1 Answer

My router wireless transmission is not working and the light (for wireless transmission) is not coming on. All other wired connections are working. How can i fix this?


which version of dg834g do you have
its its v5 then it has a button located on top of it that enables/disables wireless connection
maybe you accidentally disabled it

if its any other version of dg834g the you can enable wireless transmission through the router page

Connect to the router by typing
http://www.routerlogin.net in the address bar of a browser.
if it asks for the id and password enter
id = admin
password = admin or password or leave it empty
these are default id and passwords, if you have changed them enter the id and password that you know

go to Wireless Settings
click on the checkbox that enables wireless transmission
save settings

and you are done

Sep 29, 2009 | NetGear DG834G Wireless Router

1 Answer

Wifi


There is a possibility that the user name and password that you are using is not used for the wireless connection of the network. If you have WPA enabled on your router, you need a password with a minimum number of 8 characters. If you enabled WEP on the router, it may need 10 or 26 characters depending on what type of encryption is enabled on the router.

You can check that using the Web interface of the router. Try these steps:

1. Connect a computer to the router wired then restart the computer.
2. Launch an internet browser and type in http://192.168.0.1 or if you changed the IP, use the changed address.
3. If it asks for a user name and password, set admin as the user name and password as the router password. If you have changed the password, use the new password.
4. Click on the wireless and check the security type. Make sure that the Mac filter is disabled and there you can find the network key set on your computer.
5. You can then use that key to connect your wireless computer

Jul 30, 2008 | NetGear DG834G Router

2 Answers

BEFSR81 admin problem when enabled uPNP


I actually FOUND the solution at the linksys community forum site. It's weird, and I quote [kiefmoon], "I beat my head against this issue for the past few months, for the same reason as you: I'd built out a Windows Home Server, which can configure a home router automatically via UPnP, so I happily enabled it on the router, only to be locked out of the web-based configuration page.

Good news though! I just figured out the cause of the issue -- and it's really dumb:
You turn on UPnP on the Passwords tab, right? Well, if you look around on that page, you'll notice that, along with the option to enable UPnP, there are two password fields filled with asterisks. I think most people would assume that if they don't change anything in those fields, then click Apply, that the password has not been changed. And they'd be wrong. I don't know what the password gets changed to at that point, but it's not "admin".

...So the fix is: when you enable UPnP, do yourself a favor and enter a password in those fields (ideally something sronger than "admin" ). That way, you'll actually know what the password is when you get prompted for it."

Feb 26, 2008 | Linksys EtherFast Cable/DSL Router

Not finding what you are looking for?
Routers Logo

Related Topics:

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Mike

Level 3 Expert

4331 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...