Question about Computers & Internet

1 Answer

I have the old motherdoard model:6btml-e100n i need the instruction for installation i don t know where plug power switch led hd led power resert could you help me please

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 116 Answers

There is a cable coming from the power box that has lots of holes then find where that goes on the motherboard

Posted on Jan 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the front panel connections location, which ones go where for the ga-73pvm-s2h motherboard


Gigabyte has the manual for the GA-73PVM-S2H on the product support site: http://www.gigabyte.com/products/product-page.aspx?pid=2691#manual . The full manual is near the bottom of the list. The direct link to the English version of the manual is http://download1.gigabyte.us/Files/Manual/motherboard_manual_ga-73pvm-s2h_e.pdf . The Motherboard Installation Guide at the top of the list is a generic manual for all motherboards.

The front panel connections are shown on page 28 of the manual. There are two lines of pins. From left to right, the inside line of pins are the Power LED +, Power LED -, Power Switch +, Power Switch -, then the Case Speaker +, Case Speaker -. (The speaker - is next to a Case Fan connector; so there are a couple of blank spots between the speaker + and - pins.) On the line of pins at the edge of the board, again from left to right: HD LED +, HD LED -, Reset Switch -, Reset Switch + . There is no contact on the last pin in this group.

I hope this helps.

Cindy Wells

Jun 06, 2016 | Gigabyte Computers & Internet

1 Answer

Wiring motherboard to a atx tower


The motherboard manual will give you a breakdown of the cast-to-motherboard connections for the board. They differ slightly from board to board, but the connections are almost always found at the bottom front corner of the motherboard. There will be connections for the hard drive LED, the power LED, the power switch, the reset switch, and on some, the speaker (optional). The power switch and the reset switch connectors , 2-pin plugs, are not polarized, meaning that they can be connected to their pins either way without issue. The Power and HDD LED plugs are polarized, as LEDs have a positive and negative. Get this plug backward and the LED won't work. These are also 2-pin plugs. The power LED usually has a green and white wire (Green is +) and the HDD is usually red and white (Red is +) . Some motherboards have color-coded pins -- DO NOT TRUST THEM IF YOU DON'T HAVE A MANUAL -- they are not always standardized. Some motherboards have small print on the board adjacent to the pins to identify them. You CAN trust these. Otherwise, go to the Motherboard manufacturers site and get the manual for the board. The model number is on the board and can be searched for. If the manufacturer's name is not obvious, Google the model number and it will usually lead you to the manufacturer.

Dec 17, 2011 | Intel Motherboard

1 Answer

I clean my computer! i unplug all the switch after i clean my computer i switch all the wires when i push the power botton nothings happen because i dont know how to switch the power led,hdd led, reset...


You better read the user's manual, where you have all the instructions.

Download it from:

http://www.foxconnsupport.com/download.aspx?models=en-us0000341&category=C000000001&series=en-us0000002&keywords=&sort=Motherboard%20Manual

Jun 29, 2011 | Foxconn 45CMX socket LGA775 motherboard...

1 Answer

How to plug power switch into ASUS A8N-LA motherboard. Can't remember where power led , HD led and Power switch goes


you have a panel in the left of your ata connetor in motherboard, read there (is writen f_panel1) for apropriate led place (for example reset is writen rst, power led is writen pwr and disk led hd or hdd.)

Apr 06, 2009 | ASUS Computers & Internet

4 Answers

Asus a8v fail


does the power supply fan run when switched on.
does the hard drive spin up .
Have you reseated the video card.

Jan 26, 2008 | ASUS A8V Deluxe Motherboard

1 Answer

Front panel pin layout. I need the front panel pin layout especially for the HD IDE active LED.


Howzit
Trial n Error is your best bet on the control pins panel there are two rows, with the power plugged in,with a screwdriver touch adjacent two pins together at a time starting with the top row then the bottom row, when you touch the right two pins your motherboard will power-up, then place the power-switch plug onto those two pins (the writing on the plug facing innwards toward the mainboard) the two pins for the reset switch and 99.9% of the time located directly next to the power switch or directly above the the power pins on the other row. For the LED lights you will have to just try the different pins and the Power LED will remain on as long as your mboard is on, but to find the LED pins for the Harddrive you will have to plug in your HDD and then when it powers up try the pins and the led for the HDD will flicker on-off, that would be the correct one. Dont worry your mboard will not be damaged by this in any way. Goodluck and let me know how you go. Thanks

Regards

Oct 27, 2007 | Iwill VD133Pro Motherboard

2 Answers

P4mmv2 motherboard


see the diagram below for front panel conections

Sep 02, 2007 | EliteGroup P4VMM2 Motherboard

1 Answer

IBM NetVisat 02R4084 Mainboard


With the power on cross the pins with a slide on connector. When it fires on you know which one is the sw. When you cross the reset it will restart. When you try the HD the light will come on during HD activity. And the power light will work when you have the power light plugged. It isn't to hard. Just be careful.

Sep 27, 2006 | IBM (02R4084) Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

98816 Answers

David Payne
David Payne

Level 3 Expert

14071 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...