Question about Quinny Buzz Jogger

2 Answers

New ram for quinny buzz

Where can I get a new gas ram for my quinny buzz

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Be sure it is the gas ram and not the cast aluminium anvil which the gas ram pushes against. The symtoms are similar
This 'L' shaped casting snapped in half on our Quinny Buzz and I managed to repair it by taking the whole centre hinge apart, drilling out the pin which holds one half of the aluminium anvil in place and removing this striaght piece of the anvil.
To repair I first glued the two parts together with araldite then held them in the vice whilst drilling through both pieces to a depth of about an inch with a 4mm tapping size drill. Then seperate the two parts, tap the shank out 4mm and drill the right angled bit 4mm clearance. Reconnect the two parts using a 4mm steel screw and some 'locktight'. Replace the anvil in its slot and replace the holding pin securing with araldite.
Reassemble the whole shooting match and it works ( well ours did....and still does!)
This seems to be a common problem but I could not find any spares. Also the holding pin for the anvil is not made to come out hence having to drill it out. So I doubt if any spares are available anyway.
Not easy and you need a few engineering tools to do the job. But much cheaper than a new frame assembly.

Posted on Aug 12, 2009

  • 2 more comments 
  • tommy yalung
    tommy yalung Jul 06, 2015

    hi john i have the same problem with my pram... the other half of the l shape casting still inside the plastic tubing still thingking how to remove it

  • tommy yalung
    tommy yalung Jul 06, 2015

    you mentioned that the remaining piece inside have a kind of lock? were its located? tnx

  • j_stocking84 Jul 06, 2015

    Hi,
    It's such a long time since I wrote the article I find it hard to remember, and as we no longer have the Quinny I cannot now go to look at it..( It was still working fine When we sold it however!) I can't see where I mentioned a lock?....I know that the casting had to be removed by drilling out the pin which held it in place. You can then repair the casting as I have described. The only time I mentioned the word lock was when I said you should secure the repairing screw with 'Locktight' which is a compound which stops screws coming loose. The pin which holds the casting to the Chassis should also be secured with epoxy resin.
    Sorry can't be of any more help.
    regards
    John

  • tommy yalung
    tommy yalung Jul 06, 2015

    hi john tnx so much for your reply ill just see how to remove the other part of the L shape frame ...that support the hydraulic regards

×

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Here is the US distributor of parts for all Quinny Strollers...
Dorel Juvenile Group USA
Canton Commerce Centre
45 Dan Road
Canton, Massachusetts, USA02021
(781) 364-3100
(800) 544-1108

Posted on May 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get new foam handle covers on the quinny buzz


need to buy a new handle bar try ebay there cheap enough

Jul 27, 2012 | Quinny Buzz Three Wheel Stroller

1 Answer

I just purchased a second hand Quinny buzz 3 and I believe I need a new front tire. When I go to turn the tire bumps on the cement and prevents me from turning with ease. Where can I find a new spare tire?...


hi you can get a new wheel unit from quinny direct or eBay
the folding is something else turn the buzz over and check the groove on the middle tube to see if it is clean try an oil like wd40
if that doesn't work it may need a re gas which can done by quinny

Feb 16, 2011 | Quinny Buzz Three Wheel Stroller

1 Answer

Quinny buzz pushchair.


Yes you can, you need to get in touch with Dorel UK 01842 763 281 (Mon – Fri, 8:30 am to 4:30 pm) They supply all the spare parts and servicing for the Quinny range.

Jun 19, 2010 | Quinny Buzz Three Wheel Stroller

1 Answer

Need upgrades


We have the same model and have upgraded ours with new front wheels (all quinny buzz models are universal inc buzz 4) new back tyres. As for the seat youll need a 2009 seat frame but these are been sold as complete packages for next to nothing on ebay. I got a new seat from ebay for £30 plus 10 p&p.

Hope this helps.

Apr 23, 2010 | Quinny Buzz Jogger

1 Answer

Not fully opening


Hi,

This does sound like the gas spring needs replacing. This is something that the manufacturer needs to do for you though. I would suggest that you contact your retailer to get this rectified.

Hope this helps.

Mar 19, 2010 | Quinny Buzz Three Wheel Stroller

1 Answer

New seat frame for quinny Buzz


Hi,

You can purchase a new seat frame only by contacting www.quinny.com.

Hope this helps.

Mar 08, 2010 | Baby Gear

Not finding what you are looking for?
Quinny Buzz Jogger Logo

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quinny Baby Gear Experts

Jennifer Rock
Jennifer Rock

Level 2 Expert

105 Answers

kakima

Level 3 Expert

98792 Answers

ray gallant

Level 3 Expert

37602 Answers

Are you a Quinny Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...