Question about Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2 OHMS => Model PV2000 Car Audio Amplifier

1 Answer

PEAVEY AMP I CAN NOT GET THE AMP TO POWER ON

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 55 Answers

IF IT IS A NEW AMP IT MAY ONLY BE THAT THE REMOTE POWER WIRE IS NOT GETTING THE 12 VOLTS TO TURN ON ....IF IT IS OLD IT MAY BE ANYTHING POWER WIRE GROUND WIRE FUSES ECT... HARD TO SAY...GOOD LUCK

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hooking up other external systems



Peavey XR 1212 You may find helpful info from the Peavey site. I'm not sure how you want to configure your setup, but the tape out may be able to feed the power amp.

Mar 24, 2014 | Peavey XR1212 12 Channel Powered Mixer

1 Answer

My peavey 5150 2 will power on but no sound....


It APPEARS that the preamp tube heaters are run from DC source while the latter ones and the power output tubes are run on AC.

Check the 6.3 volts AC going to the power amp tube.

That heater power is fed through fuse F2.

I suspect you will find that fuse has a bad fuseholder or is blown. A failure in the transformer is possible and I hope that is not the case.

A heater short in a tube is possible but doesn't happen often. Replace the fuse ONCE only and if it blows again investigate why. Could be bad wiring or a bad socket or an internal short within one of the unlit tubes. Thoose are rare but still possible.

May 08, 2010 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

2 Answers

Change the voltage from 240v to 120v


Hello,

Unless there is a 240/120 switch on the back, this amplifier cannot change voltage. The only way is to replace the power transformer, and when you do that you need to use the exact model transformer Peavey uses for the 120 version. I have also seen differences in handling power outside of just a different transformer for USA/Euro models.
The differences between these two market models might be beyond what is cost-effective to convert.

If it is the Peavey blazer 158, they go for as cheap as 100 bucks here in the states. Or buy one new for 120.00 bucks and 4.99 shipping: http://www.dcmusicstore.com/Peavey-blazer-158-guitar-amplifier

Best advice: sell it for what ever you can get and buy one here.

Hope this helps!
-mike

Mar 28, 2009 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

2 Answers

Wiring my peavey 112xt subs with my peavey 2xt tops


hi don't know if you have sorted this yet, you need to wire your cables that go from sub to top +2 -2 on the speakon (on the sub end only) HTH

Jan 04, 2009 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

1 Answer

Need the instructions for a peavey 158 Rage amp


Here is the link to the Peavey 258 Rage. The difference is the 158 is 15w and the 258 is 25w.

http://www.peavey.com/assets/literature/manuals/00583600_4.pdf




Dec 27, 2008 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

2 Answers

Ive bought a Peavey 1500 pa amplifier and would like to know are the a b knobs on the front treble and bass.If they are how would I take the outputs at the back of the amp to my Soundcraft mixer.


The Peavey A/B controls are output gain controls. Your mixers stereo output goes into the amps inputs, channels A & B. The Peavey is the output stage to your speaker system. If you you connect the outputs from a power amp to the inputs of a mixer you will blow the mixers input stage, amongst many other things and possibly damage the amplifier too. The bias (Bass, Mid, Treble controls) are on the mixer, not the amplifier. Unless you are using a mixer amp, which you are not. A PA system DOES NOT work in the same way as an intergrated hi fi amp.

Nov 07, 2008 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

1 Answer

Peavey Compressor/Limiter and Peavey 3/4/5w Crossover


The correct order is Mixer>EQ>Compressor>Crossover>Amps>Speaker. Here is the link that helped me out. Scott's PA System Tutorial

Feb 13, 2008 | Peavey CROSSOVER, STEREO 2-WAY/MONO 3-WAY,...

1 Answer

Guitar amp


You can order parts directly from Peavey. You'll have to call to place the order. You can use the followng email address to check price and availability.

 

parts@peavey.com

 

For more information, the third question/answer in the list of FAQs has the phone numbers.

http://www.peavey.com/support/faq/index.cfm

Oct 14, 2007 | Peavey AMPLIFIER, 1000 WPC, DDT, 8/4/2...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peavey Car Audio & Video Experts

Glenn Boucher

Level 1 Expert

3 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

yadayada
yadayada

Level 3 Expert

63386 Answers

Are you a Peavey Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...