Question about Zanussi ZWF1430W Front Load Washer

1 Answer

Stops at 23 mins with error code e 20

Stops on 23 mins with e 20 error but sometimes it will do full cycle without stopping please help me !!!!!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

E20 is a draining problem. the first thing to check is the filter at front of machie as there may be something blocking the pump.
Before removing filter tilt machine back and place a bowl under as there will be water inside.
Thanks for using Fixya.

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stops during wash cycle for about 1 min then starts again, stops, then starts, stops then starts. Does this several times before finally finishing the cycle.


Are you getting an error code? If not, Try unplugging it for 20 minutes.
Then plug it back in, The ccu might have to be reset.

Jan 27, 2013 | Washing Machines

1 Answer

F1 error appears just right after I turned the machine.. I had to stop and tstart 3-4 times before it gets on to cycle. Then at 23 minutes F! error error comes back and I had to do the same thing (stop and...


The F1 error code means that the computer thinks a button on the touchpad is stuck. Sometimes this can be resolved by making sure the touchpad connector fits tight into the control board. The F1 code can be cleared by pushing CANCEL/OFF. If it returns the touchpad needs to be replaced .

Aug 28, 2011 | Kenmore Washing Machines

1 Answer

My washer flashes a code F35 and stops working for 20 min Then I have to restart


The F35 message indicates a failure ofthe analog pressure switch. One thing to try with thiserror is to access the pressure switch and remove the plastic hose from it andblow through the hose towards the tub. You should be able to blow through thehose without to much trouble. After blowing through thehose and clearing the line hook the hose back up to the pressure switch and trya cycle and see if the error repeats. If the error repeats then most likely the pressure switchhas failed and needs to be replaced.
Hope this helps.. A 4 thumbs-uprating is greatly appreciated for answering your free question. Thank you inanticipation.. Good luck! ;)

Jun 10, 2011 | Kenmore Washing Machines

1 Answer

LG washing machine direct drive when i put it on it washes and goes down to 9 mins then stops, sometimes an error code comes up UE? CAN U HELP PLEASE


It means Unbalanced Error, it means the machine cant balance the load during the spin cycle, normally happens if there is too little a load i.e 1 or 2 things or overloaded. It is designed to protect the bearings. If it happens with a normal load try stopping it and re-arranging the load by hand and putting it on a spin only cycle. Hope this helps.

Feb 28, 2011 | Washing Machines

2 Answers

Washing cycle stops before finishing


Hello, i have exactly the same problem. Did you find the solution?
Thanks

May 24, 2010 | Zanussi ZWD12270 Front Load Washer / Dryer

2 Answers

Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.


Good deal your machine is a Series 11.

“”Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.””

I believe this is the start of a Spin Cycle of that Wash Cycle which Wash Cycle did you have selected?

Are there any error codes to the LED display like dC or uC?

If you stop that wash cycle with the wet load and do a Spin Only cycle will it complete with no error code?

Does the wash tub bang around in Spin Only cycle with the wet clothes load?

Standing by for some feedback and I will try to help.

Here is the Service Manual and parts look up. Can you let me know if you want to try to DIY the fix?

FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

Rich

Apr 11, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Siemens stops without going into the spin cycle


when it stops is there and f:XX error code on the display? were XX is a number.

Jul 18, 2009 | Siemens WM14S794GB Front Load Washer

1 Answer

Maytag performance series washer model mhwe500vp stops mid cycle


having the same problem found in side a small black hose with a small hole in it but have no idea what this hose is for. may be it is connected to some water sensor.

Jun 27, 2009 | Maytag Performa PAV2200

Not finding what you are looking for?
Zanussi ZWF1430W Front Load Washer Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...