Question about Crosley CCW5294W Top Load Washer

1 Answer

MyCrosley top loading washer,model CW7500 20 overflowed twice.

I blew through the hose to the pressure switch to make sure it "clicked"
I ran one load with no problem,but on the next load at the spin cycle,there is a terrible grating/grinding noise coming from under the drum.I removed the agitator and drum to expose a geared shaft. the noise seems to be coming from it. Help!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 262 Answers

Ok try this look under the washer between the motor and the transmission is a motor coupler it may have broken to get to it you need to remoe the motor and the pump very easy job but look between the motor and the trany and you will be able to see the coupler it should be two plastic coggs with a rubber coupler this is usually the problem

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New whirlpool wtw6500ww cabrio washer has overflowed with water every load I ran today. What am I doing wrong? It ran over with every size load.


There is a clear hose that goes from the tub to the pressure sensor on the control board. It tells the washer when to shut off the water. It is probably either punctured or disconnected, or the pressure switch needs to be replaced. If it's new its probably still under warranty and you should have whirlpool fix it.

Jan 30, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Washer overflowed after moving Load Capacity Switch from Super to reset and then to Large load?


On this model of washer you have 4 separate components that could cause overflowing. The water valve, pressure switch, pressure switch hose & the air dome. If you have to turn the water off to prevent overflowing, I would recommend replacing the water valve. If you can turn the timer off & the water stops overflowing, I would recommend checking the pressure switch, hose & air dome.

Jan 16, 2011 | GE Washing Machines

1 Answer

Model number 11042822200


You're washing machine is probably a WHIRLPOOL. F09 is as follows

"F/09" Overflow Condition
If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.
  • Check the drain hose and make sure it is not plugged or inked.
  • Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
  • Check/Clean Drain Pump Filter of foreign objects
  • Check for Drain Pump Failure
  • Check the Inlet Valve for proper shut off
  • Check the Pressure switch for proper operation

Jul 19, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

F09 code on front load washer. What is this?


F09 error means Overflow Condition.If the Overflow contact on the pressure switch is Closed for more than 60 seconds,Overflow condition will occur.In an Overflow condition,the Door will remain locked and the Drain Pump will run constantly,even if Pause/Cancel is pressed twice and the Display is cleared.

1. Check the drain hose and make sure it is not plugged or inked.
2. Check Wire Harness connectors to the Drain Pump,Pressure Switch and Central Control Unit(CCU).
3. Check/Clean Drain Pump Filter of foreign objects.
4. Check for Drain Pump Failure.
5. Check the Inlet Valve for proper shut off.
6. Check the Pressure switch for proper operation.

Apr 11, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Water doesn't turn off. Water keeps going into washer and it overflows.


check the pressure switch hose that is attached to the tub and the switch make sure it is attached some switches can be reset take the back panel off the top of the machine to access the switch.if resetting the switch does not work then replace the pressure switch. also make sure there are no holes in the pressure switch hose

Apr 01, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Whirlpool washer overflow during wash cycle


What you can try is to get the machine empty and remove the hose that connects the pressure hose to the switch and blow air through it to make sure it is clear, then tap on the nozzle where the hose connects on the switch to make sure it is also clear.

Oct 16, 2008 | Whirlpool 3.2 cu. ft. Plus Washer

1 Answer

I have blew threw the clear tube and it still over flows?


i assume it's a top load and not a front load ..could be bad pressure switch,small hole somewhere in clear pressure switch hose or least likely a hole on inside within air dome area but not through tub to cause leak

Sep 28, 2008 | Kenmore 3.8 cu. ft. HE3t Front Load Washer

1 Answer

Whirlpool Ultimate Care II - overfilling


Yes, its called a Pressure Switch and its located behind the load level selector knob in the operator console. A common problem with these model washer (and a very minor one) is that the air hose comes loose from the pressure switch, which causes the washer to overflow. The following link explains:

http://www.fixya.com/support/r762094-washer_overflows

Read through the link I provided and inspect the pressure switch. In many cases this is the a simple problem that appears to be something major. Best of all, reattaching the air hose won't cost you anything. If you perform these steps and still have a problem, more than likely you have a failed pressure switch that requires replacement. I hope you find this information helpful. Let me know if you require additional assistance.

Sep 19, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Kenmore Elite HE 3T front load washer


Hope this helps ...... F09 is a Overflow Condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service. Potential Causes ? Check the drain hose and make sure it is not plugged or kinked ? Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) ? Check/ Clean Drain Pump Filter of foreign objects ? Check for Drain Pump Failure ? Check the Inlet Valve for proper shut off ? Check the Pressure switch for proper operation PLEASE rate my solution

Oct 04, 2007 | Kenmore 44832 Front Load Washer

Not finding what you are looking for?
Crosley CCW5294W Top Load Washer Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosley Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Are you a Crosley Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...