Question about Nintendo 64 Console

3 Answers

Pokemon stadium, and transfer pak

When I turn on my n64 a message says

"this game has not been saved at a pokemon center"

How do you save it in a pokemon center?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Were you using the Pokemon or Pokemon stadium 2 games?
Also
Were you trying to use your silver,gold,red,blue,or yellow version on the GB tower?
If so...
Boot up your Pokemon version and save it on the Pokemon center, and try again...

Posted on Dec 30, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

That is not the problem, I think you turned off the console too quickly, i.e; before it was done saving.

Posted on Dec 30, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hey i had tried to use the GB tower seens i have the nrage
but the game frezes when i select the gamepack please
help

Posted on Aug 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pokemon stadium said that i need pak but i have one


Verify that only licensed accessories are being used with the system. Unlicensed products are not fully compatible with Nintendo systems, and may not work correctly.

Check the game pak manual or packaging to verify that the game is designed to be used with the N64 Transfer Pak.

Make sure the Game Boy game pak works properly in a Game Boy system. It may be a problem with the Game Boy game pak and not the Transfer Pak.

Verify that the game paks are inserted in both the control deck and the N64 Transfer Pak. If they are not, insert them and then turn the control deck power off and back on again.

Verify that the controller is plugged into the proper controller socket on the front of the control deck. If it is not, secure it and then press reset on your control deck.

Remove and re-insert the N64 Transfer Pak, making sure the pak is fully inserted into the bottom of the controller. If it is not, secure it and then press reset on the control deck.

If possible, try another controller. If the Transfer Pak works in another controller, it may be the controller that is having a problem. Check out controller troubleshooting (click here).

If the issue persists, the Transfer Pak may need to be replaced. For information on locating replacements for older products, please click here.

Jan 02, 2013 | Nintendo 64 Console

1 Answer

Pokemon Stadium won't read my Pokemon Yellow


Well it means that the game pack was not made to work on this console at the time it is not companle with Pokemon yellow so you could try and see if it will work on a wii or wii u console. If it works with the game boy advance sp then that's fine for that system then not for the N64 console sorry Pokemon stadium 2 was not made at that time.

Feb 02, 2012 | Nintendo 64 Console

1 Answer

I can't get any game to work. We used to be able to wiggle the game or take it out and put it into the console on a different angle, but now it won;t work at all. The power light still comes on on the...


Note: It is possible that the problem you have may be game play related. For example, if you cannot defeat a particular enemy, or are missing an item you need to complete an area, the problem is likely game play related and there is nothing wrong with your game. Please check our game play help for assistance.
  1. Insert the Game Pak into the system. The Game Pak label should be facing the front of the Nintendo 64.
  2. Make sure the Game Pak firmly clicks down into place.
  3. Remove all accessories (with the exception of the N64 Expansion Pak) to see if the Game Pak works correctly without the accessory. If the game does work correctly once the accessory is removed, then the game pak and the accessory may not be compatible. Check the game pak instruction manual.
  4. Check the instruction manual for the game to see if it requires any special accessories, such as the Expansion Pak, to operate.
  5. Check the list of specific game issues to see if there are any known problems for the game you are playing.
Due to the age of the system, we no longer offer factory repairs directly from Nintendo. Please click here to find out what options are available for repair or replacement of your product.
  • Controller Error Messages (e.g. No Controller Detected)
    1. Make sure you are using all licensed accessories with your system. Make sure both the controller is licensed and any accessories you are using with the controller (Rumble Pak, Controller Pak) are licensed as well. Unlicensed products may not be fully compatible with our systems.
    2. Slide the Power Switch on the control deck to the OFF position and unplug the controller. Plug the controller back in, making sure the controller-plug is firmly inserted into socket one (on the left front ofthe control deck). Slide the power switch on the control deck to the ON position.
    3. If possible, try another controller in the left-hand port. If you have a second controller, repeat Steps 1 through 3. If the trouble disappears, the first controller may need to be replaced. For information on locating replacements for older products, please click here.

  • Character Won't Move or Moves on its Own
    1. The most common cause of this problem is when the control stick on the controller is not in the neutral position when the N64 system is turned on. The neutral position is when the control stick is centered, as it is when you hold the controller while not touching the control stick. Recalibrate the Controller by using one of the following methods:
      • Turn the power off on the system. Make sure the control stick on the controller is in the neutral (center) position, and slide the power switch to the ON position. Be sure not to touch the control stick for the first few seconds.
      • During game play you can press the L+R+START simultaneously while the control stick on the controller is in a neutral (center) position.

    2. Consult the Game Pak manual for information on the primary directional control for the game. Some game paks use the control pad rather than the control stick for character movement.
    3. Try cleaning the controller (See Below).
    4. If possible, try another controller in the left-hand port. If you have a second Controller, repeat Steps 1 through 3. If the trouble disappears, the first controller may need to be replaced. For information on locating replacements for older products, please click here..
  • N64 Sticky Buttons or Control Stick, or other controller problems Try the following cleaning procedures:
    1. Unplug the controller from the control deck.
    2. Get a clean toothbrush (no toothpaste) and a cup of warm tap water (not too hot). Do NOT pour or submerge the controller in any type of liquid.
    3. Slightly dip the toothbrush in the water (the toothbrush should not be dripping wet) and scrub the area of the controller around the buttons and control stick.
    4. Work the bristles down around the sides of the buttons and the control stick.
    5. After cleaning the controller, dry it off with a paper towel.
    6. Let the controller air dry for at least a couple of hours.
    7. Test the controller for proper response.
    If possible, try another controller in the left-hand port. If you have a second controller, repeat Steps 1 through 7. If the trouble disappears, the first controller may need to be replaced. For information on locating replacements for older products, please click here.

Transfer Pak

  1. Verify that only licensed accessories are being used with the system. Unlicensed products are not fully compatible with Nintendo systems, and may not work correctly.
  2. Check the game pak manual or packaging to verify that the game is designed to be used with the N64 Transfer Pak.
  3. Make sure the Game Boy game pak works properly in a Game Boy system. It may be a problem with the Game Boy game pak and not the Transfer Pak.
  4. Verify that the game paks are inserted in both the control deck and the N64 Transfer Pak. If they are not, insert them and then turn the control deck power off and back on again.
  5. Verify that the controller is plugged into the proper controller socket on the front of the control deck. If it is not, secure it and then press reset on your control deck.
  6. Remove and re-insert the N64 Transfer Pak, making sure the pak is fully inserted into the bottom of the controller. If it is not, secure it and then press reset on the control deck.
  7. If possible, try another controller. If the Transfer Pak works in another controller, it may be the controller that is having a problem. Check out controller troubleshooting (click here).
If the issue persists, the Transfer Pak may need to be replaced. For information on locating replacements for older products, please click here.

Controller Pak

  • Deleting Saved Information From Controller Paks Depending on the game you own, there are a couple of different ways to delete the saved information on a Controller Pak.
    1. While turning on the Control Deck, hold down the START button on Controller #1. If the programmers utilized this feature, a Controller Pak menu should appear. This menu will allow you to view and delete the contents of the Controller Pak.
    2. If the first option doesn't work, then the game pak will have a feature that can only be accessed from a game menu. For example, in Wayne Gretzky's 3D Hockey, you delete saved info from the Options screen.
    To find out the specifics of how the Controller Pak works with a particular game, check the game's instruction manual.

Expansion Pak

  • For assistance with installing the Expansion Pak, click here.

Jan 19, 2011 | Nintendo 64 Console

1 Answer

How do transfer packs work? Will it work on a nintendo DS?


A Game Pack is the game cartridge you insert to play a game. GameBoy Advance Games are not compatable with the Transfer Pak. The Transfer pack and Pokemon Stadium 2 only support the following: Pokemon Red, Blue, Yellow, Gold, Silver and Crystal versions. No Ruby will not work with the transfer pak as you will not be able to insert it, and the software would not pick it up.

May 17, 2009 | Nintendo 64 Console

1 Answer

Nintendo 64 Transfer Pak...


Try cleaing the contacts on the games and the transfer pak itself, look up how to clean games on youtube.

Jan 27, 2009 | Nintendo 64 Console

1 Answer

Nintendo 64 Pokemon Stadium Transfer Pak Error


Its most likely the controller. When you put in the pack is it loose? You could try cleaning the GB game and trying again.

Jan 26, 2009 | Nintendo 64 Console

2 Answers

How to save a game in a game pak n64


You dont actually save it to the gamepak (n64 memory card) it gets saved to the n64 cartridge via a transfer pack that plugs into where the memory goes into the controller then you can import your save with pokemon stadium into the n64 gamepack.

Jan 08, 2009 | Nintendo 64 Console

1 Answer

Kirby 64 won't hold a save file


The battery inside the game pak has died, thus, it can no longer hold a save.
Buy a special screwdriver for n64 Game Paks. Unscrew the casing, then find the battery inside the Pak. Take it (the battery) to any store that sells watches, then ask for a replacement for that battery. Plug the batery (+ side facing you) in the Pak, then screw it back together.

Your game should now save. :)

Nov 22, 2008 | Nintendo 64 Console

Not finding what you are looking for?
Nintendo 64 Console Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles Experts

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers

phil

Level 2 Expert

567 Answers

Raj Patel

Level 3 Expert

845 Answers

Are you a Nintendo Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...