Question about Washing Machines

1 Answer

Error E2 My Samsung Big Wash will not drain. E2 comes on screen. I need advice.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 416 Answers

It is drain pum error. Possible solution:
• Clean the debris filter.
• Make sure the drainage hose is installed correctly.
If wont help you need to look in drain pump/wiring
More information about error codes here:
http://downloadcenter.samsung.com/content/UM/200411/20041124151342484_B1515-01527B-0603.pdf#search=%22samsung%20big%20wash%20b1415j%22
Good Luck

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E2 error code aw-8990st toshiba wash


Toshiba top load washers have standard error codes. Depending on the display (2 or 3 digits depending on the model) it will either show E21 (or E23) or alternate E2 and -1 (or E2 and -3). Here's a list of most Toshiba washers error codes;

E1: Water doesn't drain in time or not at all
E21: Lid open
E23: Lid not locking
E31: Load imbalance
E32: Check E1 and/or E31
E5: No water coming in

You can try resetting to factory default by following the procedure: Power OFF, then pressing and holding the Super Spin Dry button, press power ON and it should beep 3 times.

Hope this helps

Jan 25, 2014 | Washing Machines

4 Answers

E9 E2 ERROR


Message = E2
Error = OVERFLOW ERROR
Cause & Solution =
The water is supplied continuously due to an defective inlet valve. Change the valve inlet.
The valve inlet is normal, but the water level sensor Change the water level sensor
(sensor pressure) is low. (sensor pressure).
The drain motor does not work - Test and if faulty change the drain pump


Message = E9
Error = SENSOR PRESSURE ERROR
Cause & Solution = The water level sensor is faulty. Change the water level sensor. (remove pressure tube and blow through it to make sure it is clear first)

Mar 10, 2012 | Daewoo Washing Machines

1 Answer

Samsung washer front load willnot rinse - no water coming out of hose to drain. E2 shows up


Hello,It is drain pump error. Possible solution:
• Clean the debris filter.
• Make sure the drainage hose is installed correctly.
If wont help you need to look in drain pump/wiring
More information about error codes here:
http://downloadcenter.samsung.com/content/UM/200411/20041124151342484_B1515-01527B-0603.pdf#search=%22samsung%20big%20wash%20b1415j%22

Thanks

May 31, 2010 | Samsung WF337AA Front Load Washer

1 Answer

Samsung b1215j code e2 lights up. any clues,


Lo M8

E2 code means it's not draining out the water properly
so look for a blockage at the pump
turn the power off to the machine
take the front bottom plastic cover off so you can access
the drain tube front right small plastic plug bout 13mm in size
get some towels and a shallow tray to catch the water
remove the small plug and drain the water ( takes age by the way )
once you've done that put the small plug back in
and then unscrew the black plastic ( they come in several colours )
pump access plug bout 50mm in size which is just to the left
of the drain tube ,, there may be a small amount of water left
in the pump but it won't be much
Once the pump access plug is removed look inside the hole
and see if you can see anything stuck in there most often
it's coins or other junk thats been left in pockets or very often
if you've kids it's going to be socks or other small clothing items
which have been sucked in to the pump
remove any blockages refit the pucp access plug
turn on the machine and put it thru a quick wash cycle
make sure it drains and spins out !!!! if not then repeat the above
procedure as you've got something else still stuck in there

good luck

Spiidi

Dec 16, 2009 | Samsung Washing Machines

2 Answers

E2 error on homemaker washing machine. I have tried eveything including reducing load down to one item. It goes through the wash cycle OK, but will not drain, then eventually flashes the E2 error on its...


I have an E2 error on the display of a homemaker washing machine model no HMWM8000. It will not pump out. The PCB does not have any visibly damaged components, which part is faulty, and how do i test a water level sensor.

Sep 13, 2009 | Washing Machines

5 Answers

Haier washing machine E2 error


normally pump filter is the best place to start it could be jamed with a coin or hair clip if you take machine outside and empty it then lay it on its side you can access the pump take it off then stand up the machine and pour hot water into the soap draw check water should run out of bottom freely taking any fluff or bits with it now take apart the pump and clean it all out dry all components before reasembly if the machine still doesent wory could need a new pump

Sep 07, 2008 | Haier XQG50-11 Front Load Washer / Dryer

1 Answer

Washing machine


E3: Over-Flow Error
- Display shows E3
- Over-Flow error occurs when the water level is too high. It can be cleared by turning POWER S/W OFF, turn POWER S/W ON and then run the drain cycle for 2 minutes. Water is drained prior to POWER S/W OFF and it is forced to be drained for 2 min if a frequency of more than 25.24 KHz is detected

Jun 23, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,016 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...