Question about RCA Scenium L50000 Television

1 Answer

How does one change the video inputs without the remote control?

Can't seem to figure out how to change the video inputs on this thing without the remote control???? I've been through the menu 100 times using the buttons on the front of the tv but can't seem to change the inputs!!!! It sure be nice to watch a DVD some day again... Any insight would be appreciated... :-0

Posted by on

  • 2 more comments 
  • Anonymous Apr 20, 2009

    I purchased a Sylvania television at a yard sale but it had no remote. I am unable to change the inputs as there is no option in the menus to do so. Several Universal remotes were tried with no luck. (Perhaps the receiver is bad as I can't imagine why a "universal" wouldn't work on a major brand like Sylvania.) Changing the channel to below 2 does not roll through the front or rear AV inputs. Autoprogramming even with a signal coming from a DVD player into the A/V jacks doesn't detect the A/V channel. About the only thing left to try is an adapter to the coax jack that can be set for channel 2 or 3 if such a thing even exists anymore. Pity; it has a great picture and doesn't appear to be very old! Looks like no video games or DVD's on this one! (I guess Al Bundy was right, "Yard sales are where idiots sell junk to bigger idiots.")

  • Jimmy Hall
    Jimmy Hall May 11, 2010

    shelbygtman: is the model # correct? i can't find that # on rca's site. let me know.peace-out



  • Anonymous Mar 14, 2014

    Need to change temperature on split system without remote control

  • Anonymous Mar 16, 2014

    change input tv without remote

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 225 Answers

If you have lost the remote, go to any electronics store and buy a universal one. I have programmed many generic remote controls, and they all work fine for adjusting the video inputs. Not all television sets allow their video inputs to be switched without the remote. Most likely you will have to buy a replacement.

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change inputs?


A better remote control is a Logitech Harmony remote. It will work every other component in your audio/video system and will never become obsolete. It programs from their website, so if you ever get a new TV or change brands of audio components, you simply revisit their website to program in the changes.

Oct 01, 2014 | Sony Rm Vlz620 - Universal Remote Control

1 Answer

I cant figure out how to change the channel to input/video on my broadband tv without a remote


This problem may be more complex than just the selection of a channel to receive video. The first problem is what channel to receive the video. Usually its received on channel 3 or 4. You select that on the video output and match it on the TV. That assumes your recorder is attached via the RF (antenna) connection. If its hooked up via the component connect then you must have a remote to select IN1 or IN2 on the TV to receive video. Remote controls are available on line. Do a search on your TV model and remote control.

May 03, 2014 | Sylvania 6420FB 20" TV

1 Answer

My Sony tv turn on but the only thing showing is Video 4 , I don't have a remote, I tried tv and video no nothing.


If it shows 'Video-4' you have to input video signals to its video-4 input terminal. No other terminal will receive any signal. To say more, you can't select its other inputs/TV, without its remote control. No universal remote control will go. Try to get its original number remote control. Contact the authorized service center for Sony to buy a genuine one.

Dec 05, 2013 | Televison & Video

1 Answer

Insignia ns27rtv can not change input without remote


As there is no menu button on the front of the TV, you must have its remote control to select he inputs.

Jan 11, 2013 | Insignia Used Original NS27RTV Remote...

1 Answer

Changing channel from cable to input


Your control TV switches at the front are bad, need to replace

May 09, 2010 | Mitsubishi WD-62725 62" Rear Projection...

1 Answer

Change video input witho remote


There might be an input button or menu button on the front of the TV (or behind a door or panel) that will let you set it for video input.

May 20, 2009 | RCA E13309 13-Inch Diagonal XL-100 Color...

3 Answers

Pioneer VSX-D608 Optical connection


The manual states that the default association of each digital input in as follows:
  • Optical 1: CD
  • Optical 2: MD
  • Optical 3: TV
  • Coax: DVD
Use the "Signal select" button to set the receiver to use a digital input, and the Dolby/DTS button (above "Signal select") to enable decoding.

As samz11 stated above, a remote is required to alter the digital input mapping.

Sep 19, 2008 | Pioneer VSX-D608 Receiver

3 Answers

Nintendo Wii box light is on but no picture or sound from my tv


sometimes just sometimes tvs are funny, some tv's call it a "input select" others call it a "mode" or simply "input" and some dont have any they just want you to goto channel 2 on the tv and go back one more channel.

ushally all these modes are listed on the remote.

is it the origional remote? or is it a universal remote.

try those things above look over the remote again see if anything resembles any of that and if not

list the make and model of your tv and if your using a universal remote we will be able to figure something out for you.

Aug 12, 2008 | Nintendo Wii Console

1 Answer

I can't figure out how to change the input to video on a broksonic tv


Hi, the remote has a TV/Video key, it's used to change the modes, it needs the remote control, the input cannot be selected from the front panel.

Feb 15, 2008 | Broksonic TV

Not finding what you are looking for?
RCA Scenium L50000 Television Logo

3,285 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72601 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...