Question about HP OfficeJet D135 All-In-One InkJet Printer

1 Answer

IDS failure, call HP message comes up - HP OfficeJet D135 All-In-One InkJet Printer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

Hope this helps you. This error is caused by either a correct or incorrect detection of air in the manifold. The steps below will clear the error condition, which should solve the problem if it is caused by an incorrect detection of air. If there really is air in the manifold, however, this procedure will not solve the problem and the printer will have to be serviced. Step 1 - Remove all printheads CAUTION: Do not touch the printhead tower. Do not remove the printhead handle. Keep printheads out of the reach of children. Figure 1: HP 14 printhead IDS Failure - c00042423.jpg 1 - Handle 2 - Tower

  1. Make sure the unit is plugged in and the power is turned on.
  2. Open the print carriage access door by lifting the handle until the door locks in place. The print carriage moves to the center.
  3. Wait two or three seconds, then unplug the power cord.
  4. Open the printhead latch. See the illustration below. Figure 2: Open the printhead latch
  5. Remove each problem printhead by lifting the printhead handle and pulling up. See the illustration below. Figure 3: Remove the printhead c00042425.jpg
Step 2 - Reset the internal error state NOTE: This step must be performed before the printheads are re-installed.
  1. Close the printhead chute.
  2. Close the access door.
  3. Plug the power cord back in.
  4. Turn on the power. The front panel should read No Printhead. Will damage Product. Insert [color name] [icon] printhead now . NOTE: The carriage may make a grinding noise when you turn the power on. This noise is normal.
  5. Open the print carriage access door by lifting the handle until the door locks in place. The print carriage moves to the center.
  6. Wait two or three seconds, then unplug the power cord.
  7. Open the printhead latch.
Before re-inserting the printheads, make sure all the electrical contacts have had at least five minutes to dry. Step 3 - Insert the printheads
  1. Place each printhead in its slot in the printhead carriage. The colored shape on the top of the printhead should match the colored shape on the proper slot on the printhead carriage.
  2. Press down firmly and evenly on both the front and back of the printhead, as shown in the illustration below. Proper seating is essential to making good electrical contact.
Figure 4: Seat the printhead c00042431.jpg Step 4 - Close and check the printer
  1. Close the printhead carriage latch and make sure the loops catch the hooks. See the illustration below. Figure 5: Loops catch hooks c00042432.jpg
  2. Snap the latch into place.
  3. Plug in the power cord.
  4. Close the print carriage access door.
  5. Turn on the power.
  6. If the error clears, a message to align the printheads may appear on the HP Officejet D and HP Officejet 7100. Press Enter to align. If the error persists contact HP. Printhead replacement will not resolve this problem - the printer will have to be serviced.

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hp 4700 has come up with message scan failure unable to scan or copy


Open the given below link and perform all the steps in that:

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01611346&cc=us&lc=en&dlc=en&product=3794615

If your issue gets fixed, please come again to give us a
vote which will really motivate me to help people in
future.

May 10, 2010 | HP Officejet Pro 8500 Wireless All-In-One...

1 Answer

I can copy a paper, but then the message comes on saying scanner failure, turn off and back on


HP Photosmart 2610 All in one Ink Jet Printer
I can only print, message says scanner failure turn powere off and on , I do this and it does does not reset

Nov 16, 2009 | HP Photosmart 2610 All-In-One InkJet...

1 Answer

To my disappointment I called Hp and spoke with their technicians for the second time regarding Ink System failure 0xc18a0001? I reset the IDS by pushing the * and # key then hit 123 and I got the message...


Hi ok try I found this I know your error not in here but it may work for It worth a try nothing to lose and it may work. I know your error code is not in this but it some times it clean the error with this type of error number you can gave it a go try not harm it Error code: 0xc18a0201, 0xc18a0206, 0xc18a0306, 0xc18a030a, 0xd0620130, 0x887dd03a, 0xd05d010d, 0xf0af8004, 0xc19ac3ff, 0xc18a050...

Reset the product:
1. Without turning off the product, disconnect the USB cable from the rear of the product.
2. Remove the cartridges from the product.
3. Wait for the 'Insert Cartridges ' message to display on the control panel.
4. Disconnect the power cord from the back of the product.
5. Wait 60 seconds.
6. Reconnect the power cord. If the product does not automatically turn on, press the Power button ( ).
7. Reinsert the cartridges, and then close any open doors on the product.
8. If you receive a prompt to print a calibration page, do so.
9. Reconnect the USB cable to the rear of the product, and then try printing again.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Oct 10, 2009 | HP Photosmart C6180 All-In-One InkJet...

1 Answer

IDS failure says call HP


check with the below link
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00296705&lc=en&cc=us&dlc=en&product=91472&lang=en
if it dint resolves try with the reset
CAUTION: Performing a semi-full reset deletes any saved phone numbers on the product.
  1. Disconnect the power cord from the product.
  2. Press and hold # and 6 while reconnecting the power cord to the product, and then release both buttons.

Sep 30, 2009 | HP OfficeJet D135 All-In-One InkJet...

3 Answers

HP Photosmart c7180: "Ink System Failure" error code Oxc18a0306


I get the ink system failure message on my hp c7180 as well as an error code of oxc18a0306.

Aug 24, 2008 | HP Photosmart D7160 InkJet Printer

2 Answers

Scanner Falure Issue


Clean Scaner Unit Properly its not easy to done
other wise all engineer

May 26, 2008 | HP LaserJet 2840 All-In-One Printer

1 Answer

New printheads and cartridges but not printing only blank sheets


Hi,

IDS (Ink Delivery System) failure is not related to the print heads at all. It pertains to that delivery system that lies between the Print head and the Ink Tank. Its a Hardware Issue, some ttime it gets fixed by resetting the printer.

Follow the below steps.

POWER DRAIN:-Turn off the printer, Unplug the power cable from printer and from the wall outlet.Press and hold ON buton for 30-60 seconds.


PARTIAL RESET:-Unplug the printer power cable while its ON, press and hold # and 3 button and connect the Power cord while holding.Wait untill the ON light flashes, then release the buttons.

----(for below reset cartridges must be removed out)---------

SEMI_FULL RESET:-Unplug the printer power cable while its ON, press and hold # and 6 button and connect the Power cord while holding.Wait untill the ON light flashes,or wait for 20 seconds,hen release the button.If the printer goes off dont worry release the button and Push the ON button.


FULL NVM RESET:-Take the Ink Cartridges out, Unplug the printer power cable while its ON, press and hold OK/ENTER button and CANCEL button and connect the Power cord while holding the buttons.keep Holding the buttons until the printer goes off ,release the button and Push the ON button.

(Notes - resets will take a while)

Thanks
RIZ

Mar 05, 2008 | HP OfficeJet d145 InkJet Printer

1 Answer

Paper failure


If you can see the black rubber feed rollers, clean with isopropyl alcohol

Oct 24, 2007 | HP 920 Plain Paper Fax

Not finding what you are looking for?
HP OfficeJet D135 All-In-One InkJet Printer Logo

796 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...