Rowenta Model DZ 9080 Leaks water

I've had the same problem with two Rowenta irons. When set to a lower temperature, the iron has a bad habit of leaking water when the steam option is on. I have to either turn up the temperature setting or shut off the steam option.

BAD BUY. iF YOUR WARRANTY DOESN'T APPLY, YOU SHOULD TAKE YOUR LOSS AND BUY A NEW IRON, BUT SOME OTHER BRAND!

I have one of these and have been battling the leak problem for years. I'm a stubborn mechanical engineer and I'm bound and determined to fix this, when in fact I should just buy another, different, iron.

The problem is then 'handle'. Built into the handle is the water tank. The water tank is made from two pieces which are then glued and screwed together. Think of taking a coke bottle, cutting it in half, and then gluing it back together. Now you see where the problem comes in... the glue they use isn't up to the task, or the heat... or the pressure... is causing the tank to leak somewhere / everywhere.

I have disassembled this several times, meticulously scraped out the old silicone, and tried several different types of silicone to re-seal. So far it always fails. It's good for a while, but maybe a couple months, before it starts leaking again.

Conclusion... BAD DESIGN. Very disappointing, because in every other respect I like this iron better than any I've ever owned.

Here's a solution . . . Do NOT buy ROWENTA! I've had 3 Rowenta irons. All of them have eventually began to dump water out of the base. . . heck, the Titanic didn't leak as much as a Rowenta iron!

Hi,
Try using different water...

Here is a tip that will help you with that problem...

My Steam Iron is Leaking Water
http://www.fixya.com/support/r5301301-steam_iron_leaking_water

heatman101

You want to run the self-clean mode. Fill with water, then over a sink, with the iron facing down, press the self-clean button. Steam will eject, along with sediment and water deposits. You may have to repeat numerous times. The iron requires soft water, if you don't have soft water at the tap then buy bottled water at the grocery store to prevent this problem.

You can also buy a cleaning solution that you mix into the water reservoir, or you can make your own by filling the iron half-full of water then add white vinegar to the fill line, then perform the self-clean mode or steam mode over a sink.

Here is a Rowenta suggestions:

The iron is leaking.


Water: Use tap water in the iron. If tap water is hard or high in organic matter, we recommend using bottled spring water or mix tap water with distilled. Do NOT use 100% distilled water. Many softening systems may cause issues as well.
Auto-Off: If iron is equipped with auto off, you need to move iron or gently shake it an allow it to heat back up before beginning to iron.
Overuse of Burst of Steam: Allow more time between each burst of steam.

The Rowenta site does not list a manual for your older model, but here is their link:

http://www.rowentausa.com/rowenta/frame.aspx

Hi,
Try using different water...

Here is a tip that will help you with that problem...

My Steam Iron is Leaking Water
http://www.fixya.com/support/r5301301-steam_iron_leaking_water

heatman101

This problem is the way that rowenta seals the water tank. If the iron is disassembled and the seal is properly put on it will not leak,, however this seal is a silicone based product and not just an off the shelf gasket. I have sealed and repaired some using a high temp silicone

Hi,
Try using different water...

Here is a tip that will help you with that problem...

My Steam Iron is Leaking Water
http://www.fixya.com/support/r5301301-steam_iron_leaking_water

heatman101

I have purchased two Rowenta irons. Both have the problem with water leakage. The entire iron looses all of it's water....both in the stand up position and the sitting down position. This happened after a couple of months for both items. I contacted Rowenta and they never responded. I will never purchase another item from them. Obviously, the irons must be defective. I'm going to contact consumer affairs.