Question about Onkyo TX-SR601 Receiver

1 Answer

When i turn up the stero the power turns off and the red standby light flashes till i turn it back on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Firstly i would disconnect all speakers and turn amp up if still does it then there is an overload in amplifier anbd needs to be repaired..

If not then connect speaker 1 at a time and try amp volume again,you could also get a multimeter and check across speaker terminals on boxes for different resistance readings..

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kenwood krx-89 standby light on please help


Krx-89 stand by light wont turn off - Fixya

www.fixya.com/support/t14712608-krx_89_stand_light_wont_turn_off
Oct 20, 2012 - krx-89 stand by light wont turn off Stero doenst play is it because thestand by light is on? How do i turn off - Kenwood Audio & Video Receivers ...

How do you turn off standby on a kenwood krx-89 stereo ...

www.fixya.com/.../t15447523-turn_off_standby_kenwood_krx_89_ster...
Dec 20, 2012 - Hi, is the red light that says power On? If not, it could just be the fuse since I had the same problem. If you take the lid off, it should be in the left ...

Read - Document Download


Dec 14, 2015 | Kenwood Audio & Video Receivers

1 Answer

What can i do to stop the red light blinking for marantz sr5007?


Turn off the power using X.
2 Press X ON/STANDBY while simultaneously pressing PRESET CH + and PRESET
CH -.
3 Once the display starts flashing at intervals of about 1 second, release the two
buttons

Aug 09, 2014 | Marantz SR5007 Home Theater AV Receiver

1 Answer

No power output or display.green standby light flashes.


Sounds like either a blown mainpower fuse or the thermal fuse for the power transformer. If the protect circuit was kicking in, the display would light up, but then turn off with a red blinking light. the green light with no display means the transformer is not getting power.

Dec 31, 2013 | Denon Avr-1610: 5.1 Ch A/V Home Theater...

1 Answer

Does not turn on


If there is no reaction at all on standby button, the receiver most likely has a problem with standby power supply or mcu. If you get flashing red standby light, there is a problem with one of the channels or main power supply. Either case you need to bring it to a reoair facility.

Dec 10, 2011 | Denon AVR-1803 Receiver

1 Answer

My receiver will not turn on and the red standby light flashes. What is wrong?


Flashing standby light shows that protection mode is activated in receiver because of some problem in output amplifier section.
Please check output amplifier section and replace defective component to fix the issue.

Jun 17, 2010 | Aiwa AV-DV75

1 Answer

Power/standby light is lit. When I try to power on, the display shows "digital" then "av surrond", then the unit powers off; the power/standby light flashes. I tried unplugging to reset, but no luck.


you receiver is reporting that the impedance of the speakers is incorrect the manual says that it needs impedance of 6 to 16 ohms and when simultaneously using a and b it needs 12 to 16 ohms. but you receiver is also saying that the problem is with the av surround digital channel so the impedance of the speakers is either too low or too high check the impedance of the speakers and if they are correct try them on another circuit and see if the problem follows the speakers.
Also, it may be that the positive wire is contacting the back of the receiver and grounding out. If so reduce the length of the bare wire and reconnect.
you may have to reset your receiver to clear this state.
turn off receiver or start from the off condition,
hold down surround mode left and right and turn on the receiver hold all 3 buttons till the display starts flashing at intervals of aproximately 1 second then release the buttons, if this fails to work try the procedure again.

Cheers!

Feb 14, 2010 | Denon AVR-1601 Receiver

1 Answer

After turning ON the power/standby switch, the unit(receiver) display comes ON (green light) then after approx.4-5 seconds the display goes OFF and the unit defaults back to the standby mode (red light). I...


Is the red light flashing at first?
The unit may be going into protect mode. Lets hope it has done the job and the receiver has protected itself from failure.
Protect mode can result from speaker wires touching each other or the Amps2_bing.gif metal case. Check that first.
It can also be caused by unstable ohm loads if too many speakers2_bing.gif are connected to any of the outputs especially zone 2.
If you can remove all speaker wires and turn the unit back on. If it stays on, turn the volume down on the main zone and zone 2 if connected. Then reconnect speaker wires.

Nov 16, 2009 | Denon AVR-485 Receiver

2 Answers

Denon avr-2106 problem!!!


You're drawing too much power from it. Sounds like maybe your sub is hooked up wrong, double check that.

Mar 06, 2008 | Denon AVR-2106 Receiver

Not finding what you are looking for?
Onkyo TX-SR601 Receiver Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

D. E. Hev

Level 3 Expert

1059 Answers

gbob59

Level 3 Expert

2963 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...