Question about Audio & Video Receivers

1 Answer

The ear connector to my wireless headset broke where can i find a replacement

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers


Just click below for electronics store online, try to order there;

Partstore.com.

www.encompassparts.com



http://servicemanuals.vstore.ca/


http://www.electronix.com/catalog/

Hope it may help you;


Regards,
VOTIT

DON’T FORGET TO RATE

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

There's a distinct crackling sound on my Headset. What can I do?


I have the same problem, but only in Windows, and only on my laptop (It's a Compaq 515). I do not get the problem if I pair it with my phone, or if I plug the receiver into any of my other computers. The big thing is: If I reboot into Linux, the noise stops.

Feb 08, 2013 | Logitech Wireless Headset H600 Overthehead...

1 Answer

Looking for ear pads for my Sony MDR IF0230 headset. Any idea where I can buy a pair?


I found where you can buy the pads for your headphones but it doesn't look like they are available anymore. This website was the only place I actually found the part and as you can see, it says "no longer available"
http://www.partstore.com/Model/Sony/Sony/MDRIF0230.aspx
Sorry

May 04, 2011 | Audio & Video Receivers

1 Answer

HDMI out jack physically broken on my rx-v1900. Fixable?


An audio repair shop should be able to get a replacement connector and swap it for you. I doubt that the part is available from Yamaha (and it would be pricy if it was). The connector shouldbe available generically. Digikey or Mouser should be a good source.

Dan

Nov 18, 2009 | Yamaha RX-V1900 Receiver

1 Answer

Have a "hold" problem with my Sony Walkman D-E350


If you are talking about a Walkman MP3 player. Try checking if your headset/ear bud plug is locked in.

Apr 14, 2009 | Audio & Video Receivers

1 Answer

The 1/8" right-angle plug on my Sennheiser ear buds broke. I was able to get the piece out of my MP3 player, but I need to replace the plug - can you help?


IF THIS IS A STANDARD .125 90 DEGREE STEREO JACK(NOT FAMILIAR WITH SENNHEISER)THEN YOU SHOULD BE ABLE TO PICK ONE UP AT ANY LOCAL ELECTRONICS OR STERIO STORE.ITS JUST A SIMPLE MATTER OF SOLDERING IT ON.THEY SHOULD CARRY SOLDERLESS ALSO.BUT BE WARNED THESE ARE NOT PRETTY.HOPE THIS HELPS.THANX FOR USING FIX-YA.PLEASE RATE.

Nov 11, 2008 | Audio & Video Receivers

1 Answer

Shure wireless headset microphone


The most likely problem is a bad connection between the jack and the internal PC board. If you can solder, you may be able to resolve this yourself. Be careful NOT to alter any of the internal coils. Try resoldering the connector and update this if that fails to resolve the problem.

Dan

Jul 29, 2008 | Audio & Video Receivers

1 Answer

The headset doesn't work - philips shm 2000 supplied with webcam spc625nc


first i would try to test another headset in place of the one that could be broke. if the other head set works then your headset has either worn out over time. or you recieved a defective one. if you cant return it cause its out of manufacture or store warranty, and you want to salvage them. you can get a cheap set of headphones take the plug, and solder it in place of the old wire which will probably be the problem.

Jun 14, 2008 | Philips Audio & Video Receivers

1 Answer

Identifying left and right ear for sound


Hi Jscreamer

Turn the balance control from left to right, The sound should fade from left to right in the same direction you turn the balance control. If it does not, then you got em on the wrong way about. They often fit better the right way around too.

regards
robotek

Jun 08, 2008 | Audio & Video Receivers

1 Answer

Bought new AH-D2000 Denon headphones. Only used a week. One earphone came detached from the headset. Looked carefully, and discovered the screw came out. Have washer and screw, but the area to put the...


This is an ongoing problem with Denons, if only your screw fell out like mine, you have to do the following to screw it back in properly.

1. You have to remove the ear cups from the head band part.
2. To do (1), you have to remove the styrofoam ear **** (the soft leather part) by press down on the soft part and rotating it counter-clockwise.
3. With the ear **** removed, you will see a total of 8 screws. 4 are flat and on a higher plane, and other 4 are inside holes. Unscrew the 4 that are bigger and on the higher plane. This will remove the plastic round back from the ear ****.
4. With the big round plastic part removed, you will now have the space to properly screw in the fallen screw.
5. Make sure to use Lock-tite to hold the screw in place so it doesn't fall out again.

May 24, 2008 | Denon Audio & Video Receivers

1 Answer

I have a buzzing noise in my ear force x1 headset for xbox in the right ear.


If left channel is clean but only the right is buzzing then it must be a wiring or connection problem.
First try a different headset ,but if that does not cure the 'buzz' then a bit more work will be required with the stereo socket where you plug the headset!

Apr 18, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68157 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...