Question about Acer AL1916W 19" LCD Monitor

1 Answer

Monitor reads no signal... - Acer AL1916W 19" LCD Monitor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Take it back and get a new one

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix my hp w17e monitor that reads "VGA no signal"? I've tried unplugging my power cord and holding the on button for 30 seconds to a minute and plugging the power cord back in it still...


VGA no signal means "no signal" from the computer on the VGA (blue plug) cable... ...if the computer works check the cord for loose connection or get a new cord...if the computer is hooked to the digital cable (DVI/white plug)...set the signal source on the monitor to digital...

Feb 14, 2011 | HP w17e Monitor

2 Answers

The problem with my monitor is that it won't read the signal cable going into it from my PC. Worked fine then when I went to turn it on it will not read the signal. Says to check line but the cable is...


You should verify if it the monitor or PC problem, you should try another monitor with this PC or try the monitor with another PC to isolate the problem first.
Here is what usually wrong with this monitor:
http://s807.photobucket.com/albums/yy352/budm/Optiquest%20Q19WB/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Nov 21, 2010 | ViewSonic Optiquest Q19wb LCD Monitor

1 Answer

The monitor reads "no signal," any ideas?


Problem in the data input board(VGA or DVI).Replace the board.

Oct 27, 2010 | Neovo F-417 17" LCD Monitor

1 Answer

Check signal cable


Check if the monitor is not working by connecting this monitor to another computer.

If the monitor woks on another pc, then the pc is the issue and not the monitor.

If monitor doesnt work on the other pc, then it's the monitor that needs replacing.

I hope this helps you :)

Jul 13, 2010 | Samsung SyncMaster 930B 19" LCD Flat Panel...

1 Answer

Screen will not stay on, getting message no input signal


The message input signal means no signal is being feed to the monitor.
Check the cable use to connect the monitor to the video card.. fix and secure the connection.
If the computer is reading and you know its working, check the video card.
Turn off the CPU disconnect the video card from the motherboard and reconnect.
Try to open your CPU and see if it reacts with your monitor. If nothing happens replace your video card

May 18, 2010 | HP Vs17 17" LCD Flat Panel Monitor

2 Answers

Inout signal out of range Answer Failed: retry


It shows out of range because the PC is sending out the video signal that is higher than the monitor can display, you need to set the PC video resolution to the native resolution: 1024 x 768 @60Hz. You can reboot the PC into save mode (hitting F8 key while booting up) then set the resolution to 640 x 480 (try 1024 x 768 if it allows you to do so), reboot and reset the resoltion to 1024 x 768 @60Hz.

Mar 06, 2010 | IBM ThinkVision L151 15" LCD Monitor

1 Answer

My flat panel moitor displays RGB no signal. I


If the other monitor has no signal as well, this proved the video card is faulty and needs to be replaced.

Dec 03, 2009 | Gateway Computer Monitors

1 Answer

No signal


This problem requires you to test both the monitor and the signal input form you cable tv setup. Set the monitor up on a computer and see if it works properly. If it does then you may have a problem with the signal conversion of the cable tv to the monitor. It also could be a weak signal that drops below the monitors sensitivity levels. Have your cable tv repairman check the signal levels on your lines. Another way to test this is to hook up is with a different monitor to test your setup and see if it works. If after testing you find, the monitor does not work properly, then you need to have it serviced. Hope This Helps.

Mar 12, 2009 | Envision 19" Widescreen Flat Panel LCD...

Not finding what you are looking for?
Acer AL1916W 19" LCD Monitor Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acer Computer Monitors Experts

 Elex
Elex

Level 2 Expert

49 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

John Trigg

Level 2 Expert

250 Answers

Are you an Acer Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...