Question about Dell 3400MP Multimedia Projector

Open Question

Dell 3400MP Projector - "temp" light blinking orange

Projector bulb went out and was replaced. Started it back up and it shut off after 15 minutes with the "TEMP" light blinking orange. According to the Dell manual, this is attributed to a defective fan. Fan was replaced. Now, it will turn on for a short period of time in which the bulb lights up and the fan spins, but the temp light still blinks and it will turn itself off after a minute or so. Any ideas?

Posted by on

5 Suggested Answers

tinamarie49
  • 34 Answers

SOURCE: Hitachi CP-X250 LCD Projector

If both lights are flashing orange, that means that the bulb needs to be replaced and the filter needs to be cleaned. Make sure you reset the counters for both after you replace them.

Posted on Dec 05, 2007

cTech1
  • 66 Answers

SOURCE: hitachi projector temp light

This is what your projector's user manual says about a flashing "TEMP" light :

"The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please make confirmation that no foreign matter has become caught in the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company."

Your user manual is available at the following link :
http://www.hitachi.us/Apps/hitachicom/content.jsp?page=Products/SupportServices/Support/DiscontinuedModels/index.html&level=4&section=Products&parent=DiscontinuedModels&nav=left&path=jsp/hitachi/forhome/DisplayTechnologiesGroup/


Posted on May 20, 2008

  • 1 Answer

SOURCE: Dell 1100mp "Temp" Light

I had the same problem and fixed it today. The fan is 70 x 70 x 20mm. I could not find the exact one, but 70 x 70 x 15 works just fine and I was able to find that fan at a Micro Center store for $8.99. The fans should be blowing air out from the front of the machine, not blowing in on the lamp.

Posted on Jul 08, 2009

projdoc
  • 2236 Answers

SOURCE: the projector doesn't turn on.power,temp,lamp orange light are on

overheated. clean it out with canned air. try again. if it still has an issue, you may have a main board problem.

Posted on Nov 12, 2009

projdoc
  • 2236 Answers

SOURCE: Powers off

clean out the projector with canned air. dust keeps in the heat the projector is trying to expell. once it's blown out, check the fans to make sure they are spinning.

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My image on my Hitachi 3lcd cp-x2515wn projector is upside down. Help!! Students are waiting!! :-/


try on the remote

menu - setup -mirror - v -invert

or
menu - main - mirror - v-invert

Jan 11, 2017 | Hitachi Office Equipment & Supplies

1 Answer

My Dell 3115cn printer will not connect to the network (it still works on USB cable), hard to believe it's broken, so can the printer system be reset?


Try turning off the printer and disconnecting power plug from wall. Hold power on button for about a minute. Then replug unit and turn power on - it should then attempt to hook up to your existing network.

If no go, try reinstalling the software that initially came with printer and was used to set up the network

Jan 10, 2017 | Dell Office Equipment & Supplies

1 Answer

B&w/gray Scanning Is Okay But Color Scanning Problem


Run ink head cleaner routine. If you cannot the list make and model of printer. Thanks.

Dec 25, 2014 | Office Equipment & Supplies

1 Answer

Laser printer makes light clicking noise when idle


When idle is potentially the fuser unit, after heating and cooling. However the print quality issue associated with the clicking sound could indicate an electrical issue. The HVPS maybe faulty causing the print quality issue (due to dependant parts) and the electrical click. In any case I would recommend calling Brother and finding the nearest authorised service agent.

Oct 20, 2012 | Brother Mfc-9840cdw All-in-one Laser...

3 Answers

HP Laserjet 3330. Scanner bulb warming up doesn't go away. I have done the "solution 1" as discribte but nothing is happening. It goes like: - i put the power on, hewlett packard is flashing, the...


How does the bulb look? Is it bright or kind of dim. The bulb warming error is designed to halt use of the machine until the scanner bulb reaches the correct output level. As these are basically a flourescent tube, they will dim over time and at a certain point they will not generate enough light to enable proper scanning. If the bulb is dim, it will require replacement.

Mar 14, 2011 | Office Equipment & Supplies

6 Answers

Printer won't recognize cartridge


I had the same problem. I'm not sure but I think I replaced the cartridges when the printer was on because I turned the printer off and removed one of the cartridges. When I turned the printer back on it recognized that cartridge but not the others. I turned the printer off again, rmoved all cartiridges and put them back in when the printer was still off. When I turned the printer on again I had no problems. So...try turning off the printer, rmove all cartridges, then put them back in and restart printer. Hope this works for you .

Nov 28, 2007 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,086 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Office Equipment & Supplies Experts

Prashant  Sharma
Prashant Sharma

Level 3 Expert

1127 Answers

The Knight
The Knight

Level 3 Expert

70983 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Dell Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...