Question about Toshiba Televison & Video

3 Answers

TV/VCR/DVD Combo won't turn on. Power button lights for 2 seconds

TV suddenly went off. When trying to turn in on by remote or manually, the power button would come on but only briefly. Night before had been watching a DVD and left it in place. Unable to open DVD area.
Just purchased the set about 14 months ago from Sears as a floor model,however noticed the sticker on the back is dated 2006. No manual included.

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toshiba Master
  • 13,433 Answers

You have possibly

A blown fuse - likely
A faulty power board -likely
A broken power button -unlikely

Note that the voltages inside a television are deadly and I would recommend having the tv looked at by a professional.

Try unpluging the tv and plug it back in after 30 minutes, that should be enought.

Posted on Jan 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

There may be some problem in the supply circuitry:-
1. Fuse is blown.
2. Transformer is burnt.
3. Power supply is faulty.

In either case I would like to add that Servicing TV is a very dangerous as it involves lethal voltages(around 25000 Volts). Please consult a qualified technician for servicing it.

Please rate me appropriately if you are satisfied with my answer,in case, if you want any clarification please get back to me.

Posted on Jan 07, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 679 Answers

Check main fuse of your TV.

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello i have a toshiba md9dm1 tv/dvd combo and i lost my remote I have a universal ge remote none of the codes work Do you know the code for my tv/dvd combo?


hi,
If you remote is a 4 digit one then the codes are
0394, 0924


If the remote is a 3 didgit one then the codes are
394, 902

MANUALLY ENTERING CODES

1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to program.

2. Press and hold the CODE SEARCH/SETUP button on the remote until the

INDICATOR LIGHT lights, then release.

3. Press and release the button for the device you are programming (TV, VCR,

DVD, etc.). For AUX, press AUX then the device button you are assigning to

AUX. The INDICATOR LIGHT will blink then remain lit.

4. Enter the three or four digit code for your device using the number buttons in the

GE Universal Remote. After your code is entered the INDICATOR LIGHT will

turn off.

5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the POWER
button. Your device should turn off
OK

Aug 03, 2011 | Toshiba MD9DM1 9 in. TV/DVD Combo

1 Answer

I need the codes for a GE universal remote for a Daewoo TV


Welcome to FixYa!

You can try the following GE Universal Remote codes for Daewoo TV:
0130
0004
0009
0100
0005
0138
0043
0140
0039
0252
0279
0444
0080
0042
0058
0017
0010
0126
0018
0127
0019

MANUALLY ENTERING CODES
1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to program.
2. Press and hold the CODE SEARCH/SETUP button on the remote until the INDICATOR LIGHT lights, then release.
3. Press and release the button for the device you are programming (TV, VCR, DVD, etc.). For AUX, press AUX then the device button you are assigning to AUX. The INDICATOR LIGHT will blink then remain lit.
4. Enter the three or four digit code for your device using the number buttons in the GE Universal Remote. After your code is entered the INDICATOR LIGHT will turn off.
5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the POWER button. Your device should turn off.

If none of the codes listed work for your device try the Code Search method described below.

USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes for your brand or if your brand is not listed, try searching for your codes by following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR LIGHT lights, then release.
3. Press and release the device button for the device you are programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will blink once then remain lit. For AUX, press AUX then the device button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least 2 seconds between each time you press POWER. Important: You may have to press POWER up to 250 times.
5. When your device turns off press the ENTER button (Should your remote model not have an ENTER button, then press the OK button.) The INDICATOR LIGHT will go off.

Thank you for using FixYa!

Have a great day.
Jas247

Apr 20, 2011 | Televison & Video

1 Answer

How do i put the code into the remote


MANUALLY ENTERING CODES
1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to
program.
2. Press and hold the CODE SEARCH/SETUP button on the remote
until the INDICATOR LIGHT lights, then release.
3. Press and release the button for the device you are programming
(TV, VCR, DVD, etc.). For AUX, press AUX then the device button
you are assigning to AUX. The INDICATOR LIGHT will blink then
remain lit.
4. Enter the three or four digit code for your device using the number
buttons in the GE Universal Remote. After your code is entered the
INDICATOR LIGHT will turn off.
5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the
POWER button. Your device should turn off.
Note: If your device does not respond to the first code listed,
repeat steps with the next code. If none of the codes listed for your
device work for your device or your brand is not listed, try the Code
Search method described below.
USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes
for your brand or if your brand is not listed, try searching for your codes by
following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR
LIGHT lights, then release.
3. Press and release the device button for the device you are
programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will
blink once then remain lit. For AUX, press AUX then the device
button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least
2 seconds between each time you press POWER. Important: You
may have to press POWER up to 250 times.
5. When your device turns off press the ENTER/SAVE button. The
INDICATOR LIGHT will go off.

Mar 01, 2011 | Jasco 24911 Remote Control

1 Answer

Instructions on how to program


Hi



Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer's Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For Your Code on next page

Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.


Thank You

Sep 18, 2010 | One For All URC4220 Remote Control

1 Answer

I need help to get a code for my sanyo tv and how to set it up.


Hi
Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page

Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.

Code for sanyo tv is 0154
Thank You

Sep 13, 2010 | One For All URC-3021 Remote Control

1 Answer

I need to program the one for all URC-3021B00 to my sony tv


Hi,
Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page

Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.

Code for sony tv are 0000, 1100, 0810



Thank You

Sep 13, 2010 | One For All URC-3021 Remote Control

1 Answer

I am trying to program my urc-4220 all for one remote to my tv and dont know how, i have an older zenith tv and need to know the steps to programing it to my tv


1. Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program before starting step 2.
2. On the remote control,press a device key once (i.e.,VCR/PVR,DVD,CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press VCR/PVR once. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions.
NOTE: To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD once.After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Use the Manufacturer’s Codes (starting on page 36) to
locate the type of device and brand name and then enter
the first four-digit code for your device. If performed correctly,
the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
5. Aim the remote control at the device and press POWER
once.The device should turn off. If it does not, repeat
steps 2 through 5, trying each code for your brand until
you find one that works. If it still doesn’t work, try
Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY.
6. Repeat steps 1 through 5 for each device you want to control.


Download the full manual for FREE with codes included from http://www.replacementremotes.com/One-For-All-Manuals/Download-FREE-URC4220-MANUAL-OPERATING-MANUAL.html

Aug 11, 2010 | One For All URC4220 Remote Control

1 Answer

Im trying to program a remote the tv is a zenith


Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page


Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.


Thanx

Aug 06, 2010 | One For All URC4110 Remote Control

1 Answer

Hello. I have a model # URC-4640Boo and am trying to set it up to work an a Sony dvd-vcr combo model # SLV-D300P and can't seem to find out how. Can you help me?


Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page



Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.


Thanx

Jul 17, 2010 | One For All URC-4605 Remote Control

1 Answer

I need codes for my emerson tv dvd vcr combo


The control codes for an Emerson combo unit are:

TV VCR/DVD
036 041
039 027
155 002
155 008
198 231

To program your remote by entering a code, follow these steps:

  1. Turn on your TV.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
  4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
  5. After the LED has turned off, aim the remote at the TV and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.
Repeat the process substituting the VCR or DVD button for the TV button.

I hope that helps.

Nov 27, 2009 | Innovage Jumbo Remote Control

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72620 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...