Paper jambs all the time

Envelopes must be fed from the Auto Sheet Feeder. Use either European DL or US Comm. Env. #10-sized envelope.
Important :

• You need to print from the computer to print on envelopes.
  
• Do not use envelopes with embossed or treated surfaces, a double flap, pressure seals, or sticker flaps.
  
• Select either DL Env. or Comm. Env. #10 in the printer driver according to the envelope size you are using. If you do not, the address will be printed in the wrong direction.
  
  

1 : Retract the Paper Support.

2 : Load the envelope against the Cover Guide (the right side of the Paper Support).
Load with the front face UP and the rear flaps DOWN on the left.
A maximum of 10 envelopes can be loaded at once.
*1 Printing orientation
*2 Make sure the flaps are folded.
Important : Make sure that the Cover Guide is set upright.

3 : Pinch the Paper Guide and slide it against the left side of the envelope.

4 : Press the Paper Feed Switch so that the Auto Sheet Feeder lamp lights up.

5 : Set the Paper Thickness Lever to the right.

In the printer driver, select 'Envelope' in Media Type, and then select 'DL Env'. or 'Comm. Env. #10' in Page Size.

Hi Good day!! To Align read this

1. Raise the input tray, which you may fold over the top for compact storage. Lower the output tray at the bottom.


2. Slide the "paper-width guide" on the input tray to the left. This is the small, adjustable tab situated where you will place the stack of paper.


3. Load a small stack of paper into the input tray. Make sure short side is forward and the print side is up. For some paper, it makes no difference which side is up. Slide the stack down until it stops.


4. Slide the paper-width guide to the right, snug up against the stack of paper to ensure proper alignment.

Method 2:

1. click start
2. click printer and faxes
3. right click your installed printer and then properties
4. click printing preferences
5. click maintenance tab
there you should see alignment option click it

Thank you for using FixYa

The is blocked by dust on the side of the paper on the image unit that would have color associated with the print. Remove all the image units and clean all the laser glass. Replace those image units also if streaking as for the paper ensure correct paper side and media type.

Hi there,

Loading Paper into your Canon MP 160 Pixma.

A) Loading Paper :
Follow this procedure:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Place a stack of paper (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Set the Paper ThicknessLever to the correct position for the paper.
Note : Set the Lever to the left for most paper. When the Lever is set to the right, the confirmation message appears before the machine starts printing.
Important : Make sure the stack does not exceed the Load Limit Mark.


B) Loading Envelopes
Follow the following steps:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Prepare the envelopes for loading.
Important : * Press down firmly on the edges of the envelopes to make the folds crisp. Also, press firmly on the area that corresponds to the edges of the back flap.
* Remove any curling by holding the edges diagonally and bending them gently.
* If the edges of the envelopes are inflated or curled, place the envelope on a flat surface. With a pen, press down while moving it from the center toward the edges of the envelope.
* Ensure that no curl or puff exceeds 1/8 in. (3mm).

3) Place the stack of envelopes (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Load the envelopes in the Auto Sheet Feeder with the short side down.
* Set the Paper Thickness Lever to the right.

Important : Make sure that the stack does not exceed the Load Limit Mark.

Hope this helps. PLease rate my response.
Thanks
Have a good day.

the fold function is only available when the option finisher fs-608 is installed . here is the steps to make a trifold on a fs-608.
1 open a one page document it can only be 8.5x11 in size.
2 click file then print and pick the konica c550 in the printer name box. click properties.
3 in the output method select print leave the paper tray on auto leave the paper size on same as original click original size to indicate 8.5x11click on the radio dial to indicate portrait under original orientation.
4under the layout tab leave the following fields blank-combination,rotate 180,skip blank pages,binding margin and image shifton the right side of the layout screen leave print type as one sided and binding direction on auto.
5 under the finish tab leave paper arrangement at its default= prioritize arranging papers.make sure there is a check mark in the fold box and select trifold in the drop down menu.
6 click ok and go to the c550 to retrieve the document

Open the back of the printer - make sure it is clear. Then remove the toner check throughout the printer - reseat the toner and try to print

hi
This clearly indicates that problem is with the rollers in the paper feed tray..to clear the obstruction-fold a sheet of paper 3-4 times lenghtwise to make it thick..insert this into the paper feed tray,behind the rollers-move it left right a couple of times....repeat this a couple of times-if no go...call tech support..printer would be replaced if in warranty...good luck

Now take a size 10 Envelope fold it so that it should become like a thin long strip........ Now Insert that Envelope on the left side corner of the Printer and move it from right to left and left to right as fast as u can for about 10 times.......... Now Insert the Ordinary Papers onto the Printer and insert both the catridges and Turn on the Printer......Now try to Print it should work........
Thanku

Your card will fold to make an inside and outside once folded, but is seen in a page layout app differently.
Take a sheet of paper and fold it in half to represent the card you will be making.
Now open it up and lay it down on a table, with the inside of the card face down.
The outside back of the card should now be on your left, and the front of the card is on the right. Use a pencil or pen to mark it as such, if you need to.
Now when you do your card layout, the cover art and text should be on the right side of the page you create in the application.
If you flip the card over, so that the inside is now facing you, you are looking at the inside of the card.
Usually, the text and signature areas would be on the right side of this page, as well.
Now, use that same guidance when you work on 'page 2' of your document. Add the text to the right side of your page, so it will be on the right inside panel after you print and fold the card.
The final step is to print it out so that the inside and outside are in the correct orientation to each other.
Be sure to feed the paper such that the top of the card is facing the same side of the paper tray when you prnt both sides. (I sometimes make a light mark in pencil which can be erasd, to be sure it goes in the right direction, since this step is easily messed up.)
Good luck.
DigiChick

Try these steps from HP

http://h10061.www1.hp.com/ccsearch/search?method=mainQuery&qry=carriage+jam&pname=HP+Photosmart+2610+All-in-One&ptype=consumer&stype=pn&spname=HP+Photosmart+2610+All-in-One&spid=421139&productBigSeriesOid=391113&pid=391116&temp_hql=s-001%2Cs-002%2Cs-004%2Cs-003%2Cs-005%2Cs-006%2Cs-017%2Cz-001%2Cc-002%2Cc-001&lang=en&ctry=us&dlc=en&mode=lz&uqry=&pname_desc=HP+Photosmart+2610+All-in-One+PSC+Printer%2FFax%2FScanner%2FCopier