Question about Hotpoint Aquarius WF210 Front Load Washer

1 Answer

Started having a noisy rinse & spin cycle, then stopped.

Hotpoint Aquarius Extra WMA 36(1300 spin)

Posted by on

  • reshma_m_pat Jan 13, 2009

    Thank you very much... Had to get the washing machine repaired as the main drum bearings had failed.£90 for the repair work.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 3,463 Answers

Open the washer door and spin the drum by hand, if it feels rough or noisy and rumbling, then the main drum bearings have failed. There should be little or no noise when you spin drum
This is a major repair, and I would not recommend a D.I.Y solution.
Other possibility is there is something in the pump, but you would only hear this when the pump is working.

Plz rate my comments.
Thanks.

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hotpoint Aquarius has suddenly started being very noisy on the spin cycle. Why is this .


heavy clothes... like jeans and all on 1 side while light clothes (cotton) on the other... causes jerks

Aug 05, 2014 | Hotpoint Washing Machines

1 Answer

I have a hotpoint aquarius WF32O and when i put


is it spinning and craccleking,,carbons faulty in motor ;;will work on spin but not lower voltage wash?
change carbons,, use genuines,only

Jun 21, 2010 | Washing Machines

1 Answer

WMA 54 Hotpoint Aquarius washing machine lights flashing


the problem here is the machine is not emptying when its supposed to, you will find it is stopping at the rinse cycles. there is a sump underneath the machine that needs to be emptied. From my experiences, 9 out of 10 hotpoints that i would of repaired with the same problem as you are having is usualy caused by using the color catcher sheets, they are a disaster.

appliancesdav@hotmail.com

pallesappliancerepairs.com

Feb 03, 2010 | Hotpoint Washing Machines

2 Answers

Hotpoint washer


common problems with timer which work like a clock and goes though the cycle, bad timer will cause it not to go through its cycle. it very cheap and easy to replace everything is all plug in.

Nov 14, 2009 | Hotpoint WMA40 Front Load Washer

1 Answer

Hotpoint fault?


Check the drain and circulation hoses for partial blockages as usually this causes such problems. Also make sure you using program with full speed spin cycle (solid spiral sign just before the dot pointing the end of chosen programme)

Mar 01, 2009 | Hotpoint WMA30 Front Load Washer

1 Answer

Hotpoint WF620 - flashing error F05


This is a drain problem. Most likely something caught in the pump which is accessed by removing the small panel at the rear/bottom of the machine. The pump slots in place and can be removed by lifting and shifting to the left. Unscrew the pump off or remove the pipes will reveal all.

Dec 13, 2008 | Hotpoint Aquarius WF210 Front Load Washer

1 Answer

Wash machine stays on wash cycle and doesnt go to rinse or spin


If the water is not getting hot, this will probably stop the programme advancing .Check heater.
Plz rate solution to prob.

Dec 10, 2008 | Hotpoint Aquarius WF000 Front Load Washer

4 Answers

HOTPOINT AQUARIUS WF 250 ON/OFF LIGHTS FLASHING


The lights are set off by the balance sensors.And if your balance sensors are  stopping    it from spinning than you first have to make sure the washer is level.You  could have bad Shocks and a bad electronic control board,.                                    

May 05, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Washer will not spin


normally i would suggest changing motor carbons for hotpoint washers, but my experience is that the WMA motor armature is weaker than the carbons, normally if there is no connection fault a replacement motor is the answer 9 times out of 10, not a job for the amature

Aug 28, 2007 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

Goes straigt to spin


TRY CHECKING THE BOARD ON THIS MACHINE ESPECIALLY THE MOTOR CONNECTION. WHAT YOU WILL AHVE TO DO IS PUT THE DIAL IN TO THE OFF POSITION ( ONLY AS GUIDE ) THEN DISMATLE THE BOARD FROM THE FRONT FACIA. HAVE A GOOD LOOK AT THE MOTOR PLUG CONNECTION SECTION OF THE BOARD CHECK TO SEE IF THERE ARE ANY TRACKS THAT HAVE BLOWN. I RECONDTION WMA ALL DAY EVERYDAY AND I HAVE HAD THIS PROBLEM BEFORE ONCE AND AM THINKING YEH THAT WAS THE PROBLEM. OR IT COULD BE THE TACO ON THE END OF THE MOTOR BUT THIS IS VERY RARE FOR HOTPOINT WMA UNLIKE THE HOOVER MACHINES.

Aug 21, 2006 | Hotpoint Aquarius WMA42 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF210 Front Load Washer Logo

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...