How to repair a tannin bed model H-24RSB

If your tanning bed is beeping and the lights are turning off but the fans are still running, it is possible that there is a malfunction with the bed's control system. Here are some steps you can take to troubleshoot the issue:

1. Check the power source: Ensure that the power cord is plugged in securely to the outlet and that the outlet is functioning properly. If you have a dedicated circuit for your tanning bed, check to see if the circuit breaker has tripped.
3. Check the bulbs: Inspect the bulbs for any signs of damage or wear. If the bulbs are old or have cracks, they may need to be replaced.
4.
5. Check the timer: Make sure that the timer is set correctly and that it is not malfunctioning. If the timer is not working properly, it may need to be replaced.
6.
7. Check the bed's manual: Consult the owner's manual for your tanning bed to see if there are any troubleshooting steps or error codes listed that may help you diagnose the problem.
8. Contact the manufacturer or a professional technician: If you are unable to diagnose or fix the issue on your own, it may be best to contact the manufacturer or a professional technician to assist you with repairing the bed

The humming noise and non-functioning fans in your Sunquest Pro 24RS tanning bed could be caused by several factors. Here are a few things you can check to diagnose the problem and potential solutions:

1. Check the power source: Make sure the tanning bed is properly plugged in and the outlet is providing sufficient power. Test the outlet with another device to confirm it is working properly.
2. Check the circuit breaker: Check the circuit breaker for the tanning bed to ensure it is not tripped or in the off position. If it is tripped, reset it and try turning the tanning bed on again.
3. Check the wiring: Check the wiring connections inside the tanning bed to ensure they are properly connected and not damaged.
4. Check the fans: The humming noise and non-functioning fans may be caused by a malfunction in the fan motor or the fan blades may be obstructed. Check the fans for any obstructions and test the fan motor with a multimeter to see if it is receiving power.
5. Call a professional: If you are unable to diagnose and repair the issue on your own, it is best to call a professional technician to service the tanning bed. They will have the necessary tools and expertise to identify and fix the issue.

In any case, it is important to exercise caution when attempting to diagnose and repair electrical equipment. Always unplug the tanning bed before attempting any repairs and do not attempt any repairs if you are unsure of what you are doing.

Blue or blue/grey exhaust smoke is invariably burning engine oil and continuous smoking is probably bad as it is mostly caused by worn out pistons, rings and bores though there are other causes from the oil pan being overfull to the engine being very dirty inside.
Failed turbo seals (if fitted) is another possible cause and with a few models even an almost blocked air filter is a possibility.

One cause that isn't encountered very often concerns a newly rebuilt engine that has used a high specification engine oil from the outset, preventing the newly machined cylinder bores and new piston rings properly bedding in. One such engine I encountered smoked badly - the oil drain holes in the piston oil control grooves had been blocked by carbon.
After dismantling and cleaning and glaze-busting the bores the engine needed no new parts at all - I used a proprietary running-in oil for 1000 miles and the engine was fine.

Bedford trucks ( a division of GM) had many smoky engines for the same reason, simply the newly introduced turbo-rated engine oils were far too good to be used before the engines had bedded in...

Try unplugging it for a few seconds or turning off the circut breaker to it. This usually resets the unit.

Check all wiring for loose connections, particularly at contactor. Check for short circuit and earth leakage

Check the fan motor, and the filter. A bad motor will smell, too.

Factory parts warranty is five years all parts one year labor. Capacitor and/or fan motor has gone out and will need replaced. The breaker will throw itself off if the condition gets bad enough. Suggest not using until repaired, turn off breaker.

you need a new on/off/speed switch from jen-air find it here: http://shared.whirlpoolcorp.com/sharedservices/dealerlocator/dealer_search.jsp?siteCd=JA_EN_US it is easy to replace. make sure the breaker is off before you remove the switch

The compressor has a short going to ground .when resetting breaker stand off to the side they can and do explode. you will need service. Tom

Fan should start at the same time as the compressor. If the fan is not running the pressure could build in the system and cause the breaker to trip. Your fan motor may need replacement, or lubricated if it is not a permanently lubricated motor bearing type. Oil ports will be located on the fan motor for front and rear bearings . There may be a dirt plug in the oil ports.