Question about Lexmark N4000e Print Server

1 Answer

HOW TO RESET LEXMARK N400E - Lexmark N4000e Print Server

Posted by on

  • Anonymous Mar 31, 2009

    I have the same print server, someone change the password and now I can not change the configuration. Thanks

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 53 Answers

Are you sure the model is N400E and not N4000E ?. Try the following steps to reset the Print Server:

1. Remove the power cable from the Print Server
2. Take a pencil and press the small button on the back of the print server. Above the button is a label with "Test" written on it.
3. While keeping this button pressed insert the power cable back into the Print Server and then let go of the button.

Hopefully this should reset your print server.

Posted on Apr 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What to do with 30.05 change "cartridge invalid refill" problem


Buy Original Lexmark Tonor.
If you refill tonor, you need a new "Tonor reset chip" - some tonor remaufacture will stock them. Cost less than $2

Aug 08, 2014 | Lexmark Laser Printers 34S0400 E 360D...

1 Answer

Where is the ip address on the lexmark


You can locate the printer IP address by viewing the printer network setup page. See the User's Guide on the software installation CD for more information on printing a network setup page.

Nov 30, 2013 | Lexmark International Lexmark S515...

1 Answer

I installed the lexmark printer on my computer but cannot use the scanner. Also the fax reads error message check the line on machine not connected properly i check it looks right. Please help


remove the data cable or LPT cable, and you use UTP cable, if lexmark to PC use the cross UTP cable, but if to LAN local area network use the straight. and the last to re instal driver. good luck

May 13, 2011 | Lexmark (12T0157) Print Server

1 Answer

How do I install my lexmark X5630 into my computer


To install Lexmark X5630 you need to drivers/ software which you can download from Lexmark Official Support for X5630
Visit the above link, select the Operating System (OS) to get the drivers. After downloading the
drivers file, double-click the file to run it and follow the on-screen instruction to install the printer drivers/ software

Let me know if any further clarification/ assistance is required.

Good Luck!
Appreciate generously, if the solution could have been of any help!
CreativeTECH

Jan 10, 2011 | Lexmark (12T0157) Print Server

1 Answer

I need to download driver for my lexmark Printer E322, how do i do it, thks


You did not say which OS you are running so it is l cant put the driver on my site for you to download which is what I would usually do. but you can go to the website below and find your operating system and download the driver for your printer.If you have any problems let me know the Operating system you are running and I would be happy to link the driver to my web to make it easy for you to download and install.

http://support.lexmark.com/index?locale=en&segment=DOWNLOAD&startover=y&userlocale=EN_CA&question=E322&productCode=LEXMARK_E322&page=answers&detectedProductFacet=CMS-CATEGORY_REF.LEXMARK.PRODUCTS.MONOLASER.LEXMARK_E322&searchid=1263695741629#1

Jan 16, 2010 | Lexmark Document Distributor Advanced...

1 Answer

I am trying to install a Lexmark, 3in1 p6210


Before plugging in the USB cable you need to install printer software.

If you have the original printer disk install software from disk.

If you do not have the disk you must download the software from Internet, follow instructions below,

Click here:Official Lexmark Drivers and Software

A web page will open, follow instructions, select model, select operative system etc., and click on download .
Chose to download the file in my documents when asked.
After downloading, find the file,double click on the file ,then if you get in troubles, follow the instructions below to reset and reinstall drivers:

  • Unplug printer USB.
  • Go to control panel >> installed printers in Windows and remove (delete ) any installed printer from printer list.
  • Download driver from website, or use the disk and run the install file.
  • Follow driver installation wizard.
  • Plug back printer when prompted from installation wizard.

Mar 01, 2009 | Lexmark Print Servers

1 Answer

Printer lexmark z43


Lexmark does not distribute replacement install disk for all models.

Contact Lexmark here, to see if the disk for your printer is available.

If you do not have the disk you must download the software from Internet, follow instructions below,

Click here:Official Lexmark Drivers and Software

A web page will open, follow instructions, select model, select operative system etc., and click on download .
Chose to download the file in my documents when asked.
Afterdownloading,findthefile,doubleclickonthe file, then if you get introubles,follow theinstructionsbelowtoreset and reinstall drivers:

  • Unplug printer USB.
  • Go to control panel >> installed printers in Windows and remove (delete ) any installed printer from printer list.
  • Download driver from website and run the file.
  • Follow driver installation wizard.
  • Plug back printer when prompted from installation wizard.
Note:someprinterdoes not work on Vista, if you do not find any driver downloadfor Vistaon your model page, that means your model is not Vista compatible.

Oct 18, 2008 | Print Servers

1 Answer

Lexmark p4350


hello froggit

you can get them here Search Results - Lexmark P4350

select you o/s and download .

riz.

May 11, 2008 | Print Servers

1 Answer

Old IP address


You can reset the MarkNet X2000 to factory defaults - which includes resetting the IP address to 0.0.0.0 like this:

1. Press and hold the Test button until all four lights stay lit simultaneously, then release the Test button.
2. When #3 and #4 lights light simultaneously, press and release #1 (the Menu button).
3. When #3 lights press and release #1 (the Menu button).
4. At this point the X2000 print server has been restored to the factory default settings and should have an IP address of 0.0.0.0.


-John

Feb 06, 2008 | Lexmark Refurbished MARKNET X2000 SERIES...

Not finding what you are looking for?
Lexmark N4000e Print Server Logo

Related Topics:

1,506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Print Servers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

old marine
old marine

Level 3 Expert

1461 Answers

Cindy Wells

Level 3 Expert

4754 Answers

Are you a Lexmark Print Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...