Question about Microsoft Xbox 360 Console
When I turn my Xbox 360 on lines come through the tv and it just freezes.
You might check out the Informative article at Ezinearticles.com to fix
the freezing problem as the article gives the information about a DIY
guide, (though i don't remember the name of the site) but you can check
the article from http://ezinearticles.com/?Xbox-360-Freezing-Fix&id=1527369
Posted on Mar 05, 2009
Try to change your av input to standard tv input
Posted on Jan 11, 2009
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
This happens a lot which is then i followed by the 3 red rings(red rings of death). is what you need to do is open your'e console, their are help video's on U tube for this. Once your is console open and you have the mother board taken out you need to remove the heat sinks which are on top of the chips. just un-snap the x clamps (on the bottom of the motherboard) and take off the heat sinks. unscrew the tabs on the bottom of the heats sinks and take them out. now take one of the heat sinks to a hardware store and find 8 screws about an inch long that screw into the heat sinks, also buy 16 plastic washers and 8 metal washers that fit onto the screws.also trey to find a BUTANE Torch this will save you from the expensive heatguns and work just as good. the last thing you need is Artic Silver 5 which can be found for 5 bucks on ebay. now once you have this you need to lay your motherboard on a flat imflammable area. light the torch and make shure it is on the LOWEST setting and that the flame is about 3/4 inch long and make a sort on hissing sound. make shure the top ofthe chips are cleaned with a paper towl of the paste. start with the torch about 3 inches over a chip and keep it moving with a sweeping motion after about 30 seconds start to get close but not to close about an inch an a half away and keep making sweeping and circular movements for about 2 min. do not get to close. now move to the next chip and do the same thing. now after ur done with the chips move the torch away about 3inches and keep heat on both chips for another minute and let them cool for a total of 10 to 15 minutes. once they are cool to the touch clean off the metal parts of the chips with alcohol (I preffer acitone too) make shure they have a mirror like finish and put a very little glob of the artic silver on the metal chips and evenly flaten it out till it covers them evenly, make shure to apply enough! ( i used the side of a allen wrench, its less messy). now on the bottom of both heat sinks, clean them off with acitone or alcohol and scrub them very firmly to get off the grime from the paste. now put one plastic washer on each screw and insert them through the bottom of the holes surrounding the chips flip the mother board over and put the other 8 plastic washers on the screws and on top of these put on the 8 metal washers. then put the heat sinks on and tighten them down. once you put the mother board in the metal casing, plug it in(dont fully essmble it yet) now test out your xbox by pressing the little button on the ring of lights board and let it boot up a usual. If it works then ur done, but if 3 red lights start blinking or two red light start blinking you need to ajust the 8 screws. through the 8 holes in the bottom of the metal casing stick a small srewdriver in there and make shure they are all snug but not to tight and then loosin each one about an 1/8 of a turn till there just a little loose. keep testing and adjusting the screws till it boots up with the green lights.
THIS WILL REPAIR 3RED LIGHTS,FREEZING,NO VIDEO, 2 red LIGHTS. in most cases 1 RED LIGHT will be fixed
GO TO A HAREWARE STORE FIND THE FOLLOWING THINGS IF YOU DONT HAVE THEM
16 platic washers
8 metal washers(make shure all the washers fit snuggly around the screws and are very thin)
8 screws about an inch long that fit heat sinks
Butane blow torch, just a small one will do
small torx wrench kit. big and small flat and phillips head screwdrivers
Posted on Feb 21, 2009
try clearing the memory cache
to clear the xbox 360's memory cache,
1. go to the system blade on your menu(should be the very last one)
2. go down to were it says memory, click on it. this should bring up your hard drive or other storage devices, press a on the one you want to empty
3. once youve gotten to the screen were it shows rename or format your storage device, input Y,X,X,LB,RB,X,X and a prompt will come up asking you if you want to empty your systems cache.
Posted on Jun 22, 2009
Tips for a great answer:
Jan 17, 2016 | Video Game Consoles & Games
Apr 01, 2012 | Microsoft Xbox 360 Console
Dec 18, 2011 | Microsoft Xbox 360 Elite Console
Oct 15, 2009 | Microsoft Xbox 360 Console
Jun 24, 2009 | Microsoft Xbox 360 Console
May 09, 2009 | Microsoft Xbox 360 Console
Apr 14, 2009 | Microsoft Xbox 360 Console
Nov 26, 2008 | Microsoft Xbox 360 Console
Apr 21, 2015 | Microsoft Xbox 360 Console
175 people viewed this question
Usually answered in minutes!