Question about Car Speakers & Subwoofers

1 Answer

Jenson Phase Linear UV8 sub input

Hi i have a Jenson Phase Linear UV8 player and there is only one blue sub connection but i have a red and a blue connection is there another spot 2 plug the other sub input into or do u just need one thanks

Posted by on

  • xx_carver_xx Jan 07, 2009

    Jenson Phase Linear UV8 which connection rca for sub input


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

U need to get a Y splitter to make that one female into 2 females so both the red and blue plug in. its like 5 bucks. one end is a male rca connection then splits to to female rca's

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i hook up my Aiwa 90 watt self powered subwoofer to this Onkya A-8037 stereo amp there are only two auxiliary ports in the back and both are used by the stereo.


Your powered subwoofer should have two different pairs of inputs - one is a line input that is connected to a subwoofer output on your amp. The other inputs are those that are directly connected to the existing speaker outputs on your amp.

When you have all working make sure that the sub output is in phase with your other speakers lest you have bass cancellation.

Jun 20, 2015 | Car Speakers & Subwoofers

1 Answer

Mackie 15 inch replacement speaker


To determine polarity of a sub, take a 9 volt battery and two one foot pieces of wire. Connect each wire to each terminal on the sub. Then touch one wire to one side of the 9 volt battery terminal and the other wire to the other side terminal. If the subs cone pushes upwards that is the correct way to hook it up(in phase which is normal). If the subs cone pulls down, is is 180 degrees out of phase. I hope that this answers your question.

Jan 14, 2014 | Insignia Car Speakers & Subwoofers

1 Answer

How to i install a Pioneer DEH-1250 to a Jensen 5500?I got these as a gift and its like confusing me.Please help me out and send me a diagram on the input wiring from the Pioneer player to the Jensen 5500-...


Hi, what you want to do is just connect the speaker wires from the head unit straight across to the pre-amp inputs of the amp. If you have a sub, also connect the pre-amp outputs of the head unit to the 2 sub inputs of the amp. Connect the blue wire of the head unit to the turn-on terminal of the amp and connect power wires to both units. May I ask what speakers are you using?

Aug 14, 2011 | Jensen Car Speakers & Subwoofers

1 Answer

Jensen DVD player (JDVD 4301) does not show picture when DvD is inserted. Message on screen "Warning Stop Watch Video" display on blue screen although I can hear the movie playing. Did I connect...


Jenson requires the green wire to be connected to the vehicle parking brake.(Safety feature) this green wire requires a negative switch to activate the screen.

Jul 29, 2011 | Car Speakers & Subwoofers

2 Answers

Hi i have two 10'' jenson xs sub and they are about 6 years old and i was wondering wut amp size i should buy to run them.


I believe these are 4ohms, if so buy a 2ohm stable monoblock amp, that puts out 250-300 watts RMS, and connect your subs to it in parallel, don't pay attention to peak watts, look at RMS watts, or continuous watts. If they're 2 ohms, buy a 2 ohm stable 2 channel amp that puts out 125-150 watts RMS per channel, and 250-300 watts total or bridged RMS output. And connect them normally, on sub per channel... hope this helps, as far as brand recommendations, MTX, pioneer, Alpine, Kenwood... Good luck

Sep 20, 2009 | Jensen XS-1010 Car Subwoofer

1 Answer

I have a fusion sub and amp and have no instructions on how to wire this can somone please help ive got green wires red wire and a small thin blue wire


Hello nicole_murra,

The green wires are for signal input to the included amp and should be connected to a pair of RCA preamp outputs on your head unit. The thin blue wire connects from "remote" on the amp to a switched 12V output on the head unit (usually blue or blue/white). The red wire is for power and goes through the fuse to positive battery. You also need to connect the amp terminal marked "ground" to the metallic chassis of your vehicle, within a distance of about 1/2 meter or less. There's usually a short piece of wire with black insulation included in most amp wiring kits. If your Fusion sub did not come with such a wire, you can use any wire that is the same gauge (or bigger) than the red power wire.

Hope this helps.

Sep 08, 2009 | Fusion FEW12PK Car Subwoofer

3 Answers

Wiring a Kenwood KSC-WD250 Subwoofer


7e83231.jpgi had the same problem Here is the diagram i used from someone else on fixya.  Thank you.

Nov 27, 2007 | Kenwood KSC-WD250 Car Subwoofer

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Speakers & Subwoofers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...