Question about Pioneer DEH-P2900MP CD Receiver /AM/FM/MP3/ CD Player

1 Answer

No sound from speakers

All of my wires are hooked up correctly but i am not getting sound out of the speakers. I can take it out and hook up the power and a speaker and it works.

Posted by on

  • 2 more comments 
  • Chris NoSay Jan 22, 2009

    I have the head unit hooked up and the sub plays but no interior speakers. Sometimes they kick on when I'm driving but very rarely. It's driving me nuts so if anyone can help please do.

  • 92caddy Mar 11, 2009

    ok so one night we were riding around and my 6x9s and door speakers just quit the subs still play and the head unit works but no lyrics and ive checked the setting on the head unit and everything is wired correct could it have something to do with the head unit.

  • Lucas Liew
    Lucas Liew May 14, 2014

    Some pioneer Deh-XXXX, power lost = Memory lost, when reconnect power back, you need go DEMO and find PREOUT ( SW & FULL) setting, set it to full power out, then you can hear sound.

  • Lucas Liew
    Lucas Liew May 14, 2014

    Some Pioneer Deh-XXXX power lost=memory lost, when you reconnect back power supply, you need to go DEMO and find PREOUT( SW & FULL), set it to full power out, then you hear sound.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had a similiar problem, i asked an electrician that, the amp rating is too low, and the sound cuts out asap.hope that helps.

Posted on Mar 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Only the back two speakers hooked up to my system are working. I am not getting any sound from the front two. Is there a way to adjust it so all four of them are playing


IF your balance is correct on your cd player and youve got good connections on both wires the speakers should work unless the front two channels are fried then theres no sound. I would try getting two extra pieces of wire 2 feet atleast and hook them up to the front two channels and to an extra speaker if youve got one then go from there.

Nov 25, 2010 | Dual Electronics XDMA6855 CD Player

1 Answer

Radio display says protect. does not emit sound.


Sounds like you have either a short in your speaker wire somewhere, wires touching in the back of the unit or a short inside the stereo itself... Try pulling the radio out and unhooking all of your speakers...Turn unit back on after all speakers are disconected...If unit still shows protect, then radio is bad...If it doesnt, power off and hook up speakers one by one and power it back on till it shows protect again....When it does, the last speaker wire you hooked up has either a crossed wire or the speaker is bad...

Oct 07, 2010 | Kenwood KDC-MP205 CD Player

1 Answer

I have power, its grounded, illumination, everything, reads my cds and ipods and even scans radio no problem but the problem is that i have ZERO sound from the speakers all wires are correctly hooked...


the pink wire is for amplifier and ur car must have one built in side under the dash or in the back or ur car or suv try to see if u might have one cause if it does not have power going to it ur speakers will not work i hope this helps.

Aug 17, 2010 | Alpine CDA-9885 CD Player

1 Answer

I have a used pioneer cd deck. No sound to speakers


The blue wire would be your remote wire to hook up a amp and if you have a wire harness all you have to do is match the colors up.

May 14, 2009 | Pioneer DEH-P3100 CD Player

1 Answer

Clarion 3475 speakers wired, player wont turn on


The RED from the clarion wire must be hooked up to a switched power source ... that was wired to your old radio, then press the reset switch, and it should then turn on.

May 05, 2009 | Clarion DRB2475

1 Answer

No sound to speakers hooked to RCA jacks.


you have the wires mixed up. the positive wire is hooked into the negative, rechech your wiring

Apr 13, 2009 | Dual XDMR-7700 CD Player

1 Answer

Clarion DXZ385USB


the message you are getting is "amp guard". This is the mesage it will display when a short in a speaker wire or speaker with low impedence is hooked to the internal amp and sends it into protect mode, shutting down the amplifier section while the rest of the unit continues to work.
Check your Factory speaker locations for blown speakers or bare wires to metal.

Dec 28, 2008 | Clarion DXZ475MP CD Player

1 Answer

Stereo hook up no sound


After all connections are completed correctly - Press the RESET button. The RESET button on the housing must be activated with either a ballpoint pen or similar pointed object. The RESET button is to be activated for the following reasons:
• Initial installation of the unit after all wiring is completed.
• Some the function buttons do not operate.
• Error symbol appears on the display.

Jul 10, 2008 | Virtual Reality Sound VR3 CD Player w/ USB...

2 Answers

Stereo display works fine, but no sound to speakers.


The wires may have gotten wet and fried something in the sound output in the stereo.

Jun 16, 2008 | Pioneer DEH-1900MP CD Player

Not finding what you are looking for?
Pioneer DEH-P2900MP CD Receiver /AM/FM/MP3/ CD Player Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

xxxxxx xxx

Level 3 Expert

4706 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Pioneer Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...