Need to reset time and name info on display for DKT301C-SD

Hi Brian,
A watch is normally an easy thing to figure out unless it has all kinds of censors on it like altimeter compass ect...
This one you have looks like you only need to hold in a button to reset the date time settings on the digital display.
And the Cap you have to twist of to get to set the time on the analog face.
Eg. try holding in the reset button, if the display starts blinking try pushing the start button to set the hours then mode to move to the next minutes then mode again to set seconds... and so on. It takes a bit of fiddling around to get the right combination. Hope it helps.

Turn off ref. for 1 min.

hi Akram.
this is all i could find out.
When the tablet is turned off, keep home button pressed.
Now turn on tablet while still holding the home button.
When white android figure appears, release both buttons.
You will get into recovery mode, you can select "restore factory settings" there.
Download the right firmware here: ONDA

Extract the content to the root of your sd card (since you cannot use your tablet, i suggest using a cardreader + pc or another tablet? or try to hook your tablet to the pc and hope it recognizes it)

There should be 5-6 files now on your SD card.

Turn on tablet while holding home button, untill white android figure appears then release.
It should update your firmware now...
or you could try this link on how to do a hard reset.
but do so at your own risk.
Onda V811 hard reset format factory mod recovery rom install ..
or try this link for more info.
hard reset tablet onda v811 Google Search
or this one.
811 Onda Tablet logo screen white Google Search

What type of reset do you want to do? For a simple system reset you would take a paperclip or similar and push in the small recessed button that should be just to the left of the SD memory card slot.
You can also perform a system reset to delete all personal info etc in the unit menu under system options.
If you need a reset because your unit is just not working anymore that can be done too, more entailed, but do-able. Let me know if that is what you need to do.

I nearly went crazy pushing buttons, but finally got the right combination. From the normal Time Display (as you would normally use the watch, no need to push any buttons) Push and Hold for a few seconds the Lap/Reset Button. The "Set" Mode will become active. Release the Lap/Reset button when Set appears in the Display. Notice in the Display a small Arrow that points to a button, either the ST/STP or Mode Button. (Initially it will be the ST/STP Button). When you depress the button to which the arrow points, the Field Flashing in the display will be set (For ST/STP) or Changed to the next Field (When the Arrow Points to the Mode Button). Simply toggle through the fields (using the Mode Button) and set (using the ST/STP Button) as needed. You will also be offered the ability to set the Month, Date, Day, 12/24 HR, and a M-D (It stands for Month - Date, in Europe it's more common to display as Date - Month). I did not change this field since by default on my watch it displayed M - D first. The setting cycle will be finished off when you have set the various fields by again pushing the Lap/Reset Button. Not related to setting the watch, but possibly useful, the Watch will completely reset if all the buttons are pushed at the same time, including pushing the Display Light (or in the case of this watch, the illumination used for the Display Characters). Hope this helps, it worked for me.

try all zeros Kryptonite locks come preset to zeros once unlocked there is a small lever inside were it locks together pull it down and set your new combo then push it back up

Try this....
My new lock didn't come with any instuctions. I followed the link above and located the "bike locks" heading. I found that the question:

- I have a Kryptonite resettable combination lock and can't find the instructions for resetting it. How can I change the combination?

contained a pdf titled :

- Resettable Combination Cable
(red reset buttons inside)

which is not the cryptoflex 1218 but is compatible anyway.

dont hurt your fingers trying to depress the nodules as the diagram says though. to my chagrin i discovered that they will turn easily if you just push them around into place.

here are the instructions:

To set your own combination
Your new lock is preset to open at 0-0-0-5 at the factory.
1. Open the lock by aligning the opening combination
number to the Guide Points and pull out the Lock
Post. (Figure 1)
2. Push down the two Reset Buttons simultaneously
with thumb and forefinger, and turn counterclockwise
until it comes to a stop. (Figure 2)
3.You are now ready to turn the dials to set your
secret combination, such as a phone number, birthday,
etc.
4. After setting your secret combination, turn the
two Reset Buttons again by Thumb and Forefinger
clockwise until it comes to a stop and back to its
original position.
5. Verify your new combination before using your
lock. Insert the Lock Post all the way into the Locking
Port but do not turn the dials. Pull out the Lock Post.
Your lock is ready to use.
6.The reset operation is now complete. Repeat
steps 1-5 anytime you wish to change your secret
combination.

Hold the arrows on the bottom right hand side until you hear a beep. The one on the left is for the hours and the right is the minutes. I tried every button combination for a month until i figured out it was triggered by holding. Hope this helps.

you just have to turn the power on, push the display button so the time is showing on the display. (The only buttons involved are the "BAND" button, the number 4 roulette button which is the top right station preset button and the "DISPLAY" button.) I think you push and hold the BAND button and while holding it push the number 4 roulette button. (you don't have to hold it for any specific time you just have to push BAND in when you push the number 4 roulette button.) the time will flash and you use the vol/seek knob to adjust the time. When done push the BAND button again.
=> This really work, thanks!

try looking for a display, or info. button on your remote, you may have to press it once or twice.