Question about Standard (CRT) Televisions

1 Answer

Hyundai TV repair parts

I have a 26" LCD Hyundai HD television. My local repair shop said I needed an ODC Control PCB board part #6870C-0036D. I have been unable to locate this part and the US distributor for this TV is apparently no longer in business. Can you help me find such a part? The model number for the TV is HLT-2672. I purchased it online in December of 2005. Thanks for any help you can give.

John Merritt A red key on the screen

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,267 Answers

I've search for this board by part number and it came up that this website has the board for your TV. Contact them for more info.
Good Luck.

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My vizio 47in LCD tv is making a high pitch noise while watching the tv. The directv is conected with an hdmi cable. Any solutions or explanations. The tv is 7 months old


Actually someone would have to open set and power it up--try to locate area where sound here is coming from.

The first place would be in the power supply which will have a number of transformers (not giant ones) that can vibrate hard enough to make a high pitched buzz or sound.

If localized to a single board the board can be replaced but in our shop if we have narrowed it down to a single part--usually some hot glue on the offending part can remove the sound---issue is not usually one that will cause a failure but irritates people in the same room with the set.

Since the set will have to be opened first to see or in this case hear where the sound is coming from it may be repairable without replacing a board.

SD TECH

May 05, 2012 | Vizio Standard (CRT) Televisions

1 Answer

Magnavox 51MP6200D/37


The conversion board needs replaced.

Dec 11, 2007 | Philips Magnavox 27MS343S 27" TV

1 Answer

The TV 's blue light comes on indicating the TV is on but there is no picture or sound.


Hello alaws,

Welcome, and thank you for using FixYa!

Your issue will require some diagnostic from your local TV Repair Shop. In today's market, unless you find a repairman that does this work for a hobby, the cost of the parts and labor is higher than the value of the TV.
It may be in your best interest to research the LCD and LED TVs at your local WalMart/KMart/Best Buy.

Have a great day!

Sep 12, 2011 | SunBriteTV Standard (CRT) Televisions

1 Answer

My 11 yrs old 25"


No,the tv main logic pcb board have dead components parts on it and also the tv video boad too.This tv must take to tvs shops and get estamate see it is worth the priced to be repair or compair the prices could be cheaper just replace another tv.

Aug 10, 2011 | Sony FD Trinitron WEGA KV-24FS120 24" TV

1 Answer

Power light is on, when I press the power with either the remote or the top panel, I hear a click then a short little whistle and then nothing and it locks up with no reponse to the power button until I...


This tv is a analoge CRT tube tv?Yes,not likely to find one out there in the internet land.Because these tv boards or parts not in productions anymore.Tries tvs local repairs shops are ur best chances for repairing analoge CRT tube tv,compare for the prices between a new LCD tv and repairing the old CRT analoge tube tv and u decide,which it better deal fo u.

Jun 18, 2011 | RCA 32V524T TV

1 Answer

Tv part


In the user book, there should normaly be a list of local service reps. I am sure you can Google for RCA service parts. They can supply the parts for their TV sets if the set is not obsolete. You will find it much cheaper to buy a new set rather than buy complete populated main circuit board.


Jerry G.

May 23, 2008 | RCA 20F514TD 20" TV

1 Answer

Where can I get the part?


Take your board to the local TV repair shop. They will be able to replace the individual micro switches and save you a small fortune replacing the whole control board.

Apr 13, 2008 | RCA F36669 36" TV

1 Answer

Cable plug in back forcefully removed.


The cable conmnector (F-connector) attaches directly to the tuner board. There is only the center connection and the ground connection. This is a simple repair for a shop but requires a bit of practice (you can't melt the inner insulator). The part costs around $2. Check with a local shop for their repair charge.
Dan

Apr 07, 2008 | Sharp 25VT-J100 TV

1 Answer

Bush 26 lcd tv


If the TV goes off completely, then is usually a faulty power board.

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Apr 05, 2008 | Bush 5693D 24" TV

1 Answer

RCA F27683GY 27" TV


I bet both TV's are connected to cable TV? This was a problem and required different fixes. There was a law suit against RCA for this issue as they said there was nothing wrong with thier TV's that it was a cable issue. You will probably have to contact a local TV shop for repairs as just audio boards won't fix the problem.

Mar 22, 2007 | RCA F27683GY 27" TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...